POST-COLLISION DIAGNOSIS




SRS-ECU MEMORY CHECK


1.
2.
note If the battery power is not supplied because of the collision impact, M.U.T.-III and SRS-ECU cannot communicate with each other. When this occurs, check or repair the instrument panel harness.
3.

REPAIR PROCEDURE



<DRIVER’S AND FRONT PASSENGER’S AIR BAGS ARE DEPLOYED>


1.Replace the following parts with new ones.

  • SRS-ECU (Refer to ).
  • Driver’s air bag module (Refer to ).
  • Passenger’s (front) air bag module (Refer to ).
  • Seat belt with pre-tensioner (Refer to ).
  • Front impact sensor (Refer to ).
  • Passenger’s (front) air bag lid assembly (Refer to GROUP 52A - Instrument Panel Assembly ).
2.Check the following parts. If there is an abnormality, replace with new parts.

  • Clock spring (Refer to ).
  • Steering wheel, steering column assembly

    • (1) Check that the driver’s air bag module is installed to the steering wheel correctly.
      (2) Check the steering wheel for noise, binding, operational failure, and play.
      (3) Check the shock absorbing mechanism of steering column shaft assembly (Refer to GROUP 37 - On-vehicle Service ).
3.Instrument panel assembly (Refer to GROUP 52 - Instrument Panel Assembly ).
4.Check the wiring harness for binding, the connector for damage, and the terminal for deformation (Refer to ).

<SIDE AND CURTAIN AIR BAGS ARE DEPLOYED>


1.Replace the following parts with new ones.

  • SRS-ECU (Refer to ).
  • Front seatback assembly (Refer to ).
  • Curtain air bag module (Refer to ).
  • Side impact sensor (Refer to ).
  • Headlining (Refer to GROUP 52A, Headlining ).
  • Front pillar trim, centre pillar trim upper, quarter trim upper (Refer to GROUP 52A - Interior Trim ).
2.Check the wiring harness for binding, the connector for damage, and the terminal for deformation (Refer to ).

<AIR BAG NOT DEPLOYED BECAUSE OF LOW-SPEED COLLISION>


1.Check the SRS air bag components and pre-tensioner according to the following procedures.
2.If a crack, deformation, or others are visually detected to the SRS air bag components or pre-tensioner, replace them with new parts.
3.Check the operation of seat belt. If the seat belt cannot be drawn out, replace the seat belt with a new one.
4.For removal and installation of parts, refer to "Servicing the SRS air bag/seat belt with pre-tensioner" .

SRS-ECU



1.Check the SRS-ECU case and bracket for dent, crack, or deformation.
2.Check the connector and wiring harness for damage, and the terminal for deformation.
3.Check that SRS-ECU is installed correctly.

DRIVER’S AND PASSENGER’S (FRONT) AIR BAG MODULE


1.Check the pad cover for dent, crack, or deformation.

2.Check the connector for damage, the terminal for deformation, and the harness for binding.
3.Check the inflator case for dent, crack, or deformation.
4.Check that the air bag module is installed correctly.

CLOCK SPRING



1.Check the connector and protector tube for damage, and the terminal for deformation.
2.Check the case for damage.

STEERING WHEEL, STEERING COLUMN ASSEMBLY


1.Check that the driver’s air bag module is installed to the steering wheel correctly.
2.Check the steering wheel for noise, binding, operational failure, and play.
3.Check the shock absorbing mechanism of steering column shaft assembly (Refer to GROUP 37 - On-vehicle Service ).

PRE-TENSIONER



1.Check the pre-tensioner for dent, crack or deformation.
2.Check the connector for damage and the terminal for deformation.

FRONT IMPACT SENSOR



1.Check the front impact sensor for dent, crack or deformation.
2.Check the connector for damage, the terminal for deformation, and the harness for binding.

FRONT SEAT ASSEMBLY (WITH BUILT-IN SIDE AIR BAG MODULE)



1.Check that the side-airbag module deployment part of the seat is normal.
2.Check the connector for damage, the terminal for deformation, and the harness for binding.

SIDE IMPACT SENSOR



1.Check the centre pillar and quarter trim lower for deformation.
2.Check the side impact sensor for dent, crack, deformation, or rust.
3.Check the connector for damage, the terminal for deformation, and the harness for binding.

CURTAIN AIR BAG MODULE



1.Check that the curtain air bag deployment part of the headlining is normal.
2.Check the inflator surface for cracks, dents or deformations.
3.Check the connector for damage, the terminal for deformation, and the harness for binding.

PASSENGER’S AIR BAG CUT OFF SWITCH


1.Check the passenger’s air bag cut off switch for dents or deformation.
2.Check the installation of the passenger’s air bag cut off switch.

HARNESS CONNECTOR


Check the wiring harness for binding, the connector for damage, and the terminal for deformation (Refer to ).