Item No.
|
Display on M.U.T.-III
|
Check conditions
|
Normal condition
|
1
|
ACD control mode
|
TARMAC is selected (displayed on multi information display).
|
TARMAC
|
GRAVEL is selected (displayed on multi information display).
|
GRAVEL
|
SNOW is selected (displayed on multi information display).
|
SNOW
|
2
|
T/M gear position hold request
|
Perform a test run of the vehicle.
|
Retention requested
|
ON
|
Retention not requested
|
OFF
|
3
|
System fail
|
Normal
|
Correct
|
Faulty
|
Malfunction
|
4
|
ACD target torque (for Meter)
|
Perform a test run of the vehicle.
|
0 - 5 seg
|
11
|
Steering angle sensor
|
Steering wheel: Steered 90° to right
|
R90 deg
|
Steering wheel: Steered 90° to left
|
L90 deg
|
12
|
Steering angle speed
|
Steering wheel: Without steering wheel operation
|
0 deg/s
|
Steering wheel: With steering wheel operation
|
Changes depending on the turning speed.
|
13
|
Steering angle sensor (status)
|
Normal
|
Correct
|
Faulty
|
Malfunction
|
Neutral point not learned
|
Neutral not learned
|
Neutral point not learned or failed
|
Neutral not learned and Malfunction
|
14
|
Accelerator position
|
Release the accelerator pedal
|
18 - 22%
|
Depress the accelerator pedal
|
Increases in response to the depression amount
|
Accelerator pedal fully opened
|
80% or more
|
15
|
Engine speed
|
Idling and test run
|
Nearly the same as the tachometer display
|
16
|
Engine torque (Driver request)
|
Operate the accelerator pedal
|
The torque changes
|
17
|
T/M Gear position
|
Shift lever position: P
|
P
|
Shift lever position: R
|
R
|
Shift lever position: Drive at D
|
D1 - D6
|
Shift lever position: Manual mode
|
M/T
|
18
|
FL wheel speed (raw value)
|
- (reference because of rpm)
|
-
|
19
|
FR wheel speed (raw value)
|
20
|
RL wheel speed (raw value)
|
21
|
RR wheel speed (raw value)
|
22
|
FL wheel speed sensor
|
Perform a test run of the vehicle.
|
Nearly the same as the speedometer display
|
23
|
FR wheel speed sensor
|
24
|
RL wheel speed sensor
|
25
|
RR wheel speed sensor
|
26
|
Yaw rate sensor
|
Perform a test run of the vehicle.
|
-100 - 100 deg/s
|
29
|
Lateral G sensor
|
Vehicle is stopped (horizontal state).
|
-1.1 - 1.1 m/s2
|
Perform a test run of the vehicle.
|
-10 - 10 m/s2
|
31
|
Longitudinal G sensor
|
Vehicle is stopped (horizontal state).
|
-1.1 - 1.1 m/s2
|
Perform a test run of the vehicle.
|
-10 - 10 m/s2
|
39
|
Stop lamp switch
|
Brake pedal: Depressed
|
ON
|
Brake pedal: Released
|
OFF
|
40
|
Parking brake switch
|
Parking brake lever: Pulled
|
ON
|
Parking brake lever: Released
|
OFF
|
41
|
Back up lamp switch
|
Shift lever: Operated to reverse
|
ON
|
Shift lever: Other than above
|
OFF
|
42
|
Ignition switch
|
Ignition switch: ON
|
ON
|
Ignition switch: START
|
START
|
43
|
Battery voltage
|
Ignition switch: ON
|
System voltage
|
44
|
IOD fuse
|
Fuse inserted
|
ON
|
Fuse removed
|
OFF
|
45
|
Odometer
|
Ignition switch: ON
|
The same as the meter display
|
46
|
ETACS coding status
|
Coding incomplete
|
Not complete
|
Coding data requested
|
Data request
|
Coding completed
|
Complete
|
47
|
ECU connection (ABS)
|
ASC-ECU connected
|
Present
|
ASC-ECU disconnected
|
Not present
|
48
|
ECU connection (ENGINE)
|
Engine-ECU connected
|
Present
|
Engine-ECU disconnected
|
Not present
|
49
|
ECU connection (T/M)
|
SST-ECU connected
|
Present
|
SST-ECU disconnected
|
Not present
|
50
|
ECU connection (SAS)
|
Steering sensor connected
|
Present
|
Steering sensor disconnected
|
Not present
|
51
|
Coding status
|
Coding incomplete
|
Not complete
|
Coding completed
|
Complete
|
52
|
T/M type
|
5M/T
|
5M/T
|
TC-SST
|
SST
|
53
|
Rear diff type
|
Mechanical differential
|
LOM
|
AYC differential
|
AYC
|
58
|
ABS fail flag
|
Faulty
|
ON
|
Normal
|
OFF
|
59
|
ABS activation flag
|
Activated
|
ON
|
Not activated
|
OFF
|
65
|
ASC fail flag
|
Faulty
|
ON
|
Normal
|
OFF
|
66
|
ASC switch mode
|
When ASC is ON
|
ON
|
When ASC is OFF
|
OFF
|
68
|
ASC activation flag
|
Activated
|
ON
|
Not activated
|
OFF
|
83
|
IG1
|
ON
|
ON
|
OFF
|
OFF
|
84
|
ECU power supply voltage
|
Ignition switch: ON
|
10 - 16 V
|
85
|
Output load voltage
|
Ignition switch: ON
|
10 - 16 V
|
86
|
Pressure sensor power voltage
|
Ignition switch: ON
|
Approx. 5 V
|
87
|
Pressure sensor output voltage
|
During electric pump motor operation
|
1.86 - 2.67 V
|
88
|
Pressure sensor
|
During electric pump motor operation
|
1- 1.6 MPa
|
89
|
Mode SW
|
Mode selection switch: Pressed
|
ON
|
Mode selection switch: Released
|
OFF
|
92
|
ACD proportion valve (indicated)
|
During ACD operation
|
50 - 1,000 mA
|
96
|
Motor relay drive indication
|
ON
|
ON
|
OFF
|
OFF
|
97
|
Yaw rate sensor (adjusted value)
|
Ignition switch: ON
|
-6 - 6 deg/s
|
98
|
SAS (adjusted value)
|
Ignition switch: ON
|
-15 - 15 deg
|
99
|
Lateral G sensor(adjusted value)
|
Ignition switch: ON
|
-1.7 - 1.7 m/s2
|
100
|
Longitudinal G (adjusted value)
|
Ignition switch: ON
|
-3 - 3 m/s2
|
101
|
Chassis Number writing counter
|
Ignition switch: ON
|
Writing count
|
102
|
Chassis Number (original) lock
|
Ignition switch: ON
|
Locked
|
Lock
|
Unlocked
|
Unlock
|
103
|
Mileage counter
|
Ignition switch: ON
|
Counter value
|
104
|
Coding counter
|
Ignition switch: ON
|
Coding count
|