LOWER ARM BALL JOINT AXIAL PLAY CHECK
INSPECTION
REMOVAL AND INSTALLATION
LOWER ARM BALL JOINT COVER CHECK
REMOVAL AND INSTALLATION
LOWER ARM BUSHING REPLACEMENT <2WD (except High rider)>
GENERAL INFORMATION
INSPECTION
INSPECTION
SPECIAL TOOLS
SERVICE SPECIFICATIONS
INSPECTION
FRONT WHEEL ALIGNMENT CHECK AND ADJUSTMENT <2WD (except High rider)>
REMOVAL AND INSTALLATION
INSPECTION
DISASSEMBLY AND REASSEMBLY
REMOVAL AND INSTALLATION <2WD (High rider), 4WD>
INSPECTION
REMOVAL AND INSTALLATION <2WD (except High rider)>
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION <2WD (except High rider)>
LOWER ARM BUSHING REPLACEMENT <2WD (High rider), 4WD>
FRONT WHEEL ALIGNMENT CHECK AND ADJUSTMENT <2WD (High rider), 4WD>
REMOVAL AND INSTALLATION <2WD (High rider), 4WD>
FRONT BODY
SIDE BODY
CARRIER
INTERIOR
FRONT BODY
CARRIER
UNDER BODY
FRAME
FRAME
REAR BODY
REAR BODY
INTERIOR
FRAME
CARRIER
FRAME
SUSPENSION INSTALLATION DIMENSIONS
UNDER BODY
SUSPENSION INSTALLATION DIMENSIONS
SUSPENSION INSTALLATION DIMENSIONS
SUSPENSION INSTALLATION DIMENSIONS
SUSPENSION INSTALLATION DIMENSIONS
REAR BODY
INTERIOR
SIDE BODY
CARRIER
FRAME
SIDE BODY
FRONT BODY
BODY DIMENSIONS AND MEASUREMENT METHODS
SUSPENSION INSTALLATION DIMENSIONS
FRAME
UNDER BODY
REAR PANEL POWER WINDOW ANTI-TRAP FUNCTION INSPECTION
REMOVAL AND INSTALLATION
TROUBLE SYMPTOM CHART
Inspection Procedure 1: Rear Panel Power Window does not Work at All.
Inspection Procedure A-4: Selector "P" position-linked door unlock function does not operate normally.
REMOVAL AND INSTALLATION
WEATHERSTRIP
Code No.2004: P/W (AS) Sensor fail (earth)
DOOR FIT ADJUSTMENT
INSPECTION
HOW TO REGISTER ENCRYPTED CODE
Inspection Procedure B-1: Each Button Signal of the Keyless Entry Transmitter is not Received.
REMOVAL AND INSTALLATION
POWER WINDOW INITIALIZED ADJUSTMENT
REMOVAL AND INSTALLATION
CHECK OF KEY LOCK PREVENTION FUNCTION
Code No. 5001: P/W (RP) SW pulse 1 disconnection
KEYLESS ENTRY SYSTEM
Inspection Procedure B-5: Relevant Power Window(s) do not Work by means of the Front Passenger’s Power Window Sub Switch and Rear Power Window Sub Switches.
CHECK CHART FOR TROUBLE SYMPTOMS
BODY SHELL
INSPECTION
SUNROOF INITIALISATION
Inspection Procedure A-3: A Door cannot be Locked or Unlocked by the Central Door Locking System
CUSTOMISE FUNCTION
Inspection Procedure 3: Sunroof Anti-trap Function does not Work Normally.
Inspection Procedure B-9: Power window anti-trap function does not work normally.
REMOVAL AND INSTALLATION
SERVICE SPECIFICATIONS
Code No.3002 P/W (RL) SW pulse 2 disconnection
LUBRICANT
Inspection Procedure 1: The Sunroof does not Work at All.
Code No.1005: P/W (DR) 3 Times jam-protection
REMOVAL AND INSTALLATION
Code No.4005: P/W (RR) 3 Times jam-protection
TROUBLE SYMPTOM CHART
DIAGNOSIS TROUBLESHOOTING FLOW
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
ADJUSTMENT OF HOOD HEIGHT
Code No. 5003: P/W (RP) Above window position
Code No.3005: P/W (RL) 3 Times jam-protection
Code No.1003: P/W (DR) Above window position
FUEL FILLER LID
SPECIAL TOOLS
Code No.2002 P/W (AS) SW pulse 2 disconnection
REAR GATE PANEL FIT ADJUSTMENT
ADJUSTMENT OF CLEARANCE AROUND HOOD
GENERAL INFORMATION
WATER TEST
INSPECTION
Inspection Procedure B-8: Power window anti-trap function does not work normally.
REMOVAL AND INSTALLATION
SHIFT "P" INTERLINK DOOR UNLOCK FUNCTION CHECK
Inspection Procedure 2: Any of The Sunroof Switch Positions is Defective.
INSPECTION CHART FOR DIAGNOSIS CODE
Inspection Procedure 3: Rear Panel Power Window Anti-trap Function does not Work Normally.
Inspection Procedure A-4: The Timer Lock Function does not Work after the Doors have been Unlocked by the Keyless Entry System.
GLASS SLIDING MECHANISM CHECK AND ADJUSTMENT
REAR GATE OUTSIDE HANDLE ADJUSTMENT
REMOVAL AND INSTALLATION
Code No.2002 P/W (AS) SW pulse 2 disconnection
DOOR LOCK
Inspection Procedure 5: Rear Panel Power Window Timer Function does not Work Normally.
Code No. 5004: P/W (RP) Sensor fail (earth)
REMOVAL AND INSTALLATION
Code No.2001: P/W (AS) SW pulse1 disconnection
Code No.3008: P/W (RL) Parameter read failCode No.3009: P/W (RL) Position read fail
HOOD
REMOVAL AND INSTALLATION
KEYLESS ENTRY SYSTEM INSPECTION
Inspection Procedure 4: Rear Panel Power Window-ECU cannot Communicate with ETACS-ECU.
REMOVAL AND INSTALLATION
ADHESIVE
INSPECTION
Inspection Procedure B-2: The Key Reminder Switch Signal is not Received.
DISASSEMBLY AND REASSEMBLY
DIAGNOSIS CODE CHART
REMOVAL AND INSTALLATION
Code No. 5005: P/W (RP) 3 Times jam-protection
Inspection Procedure A-2: A Door cannot be Locked or Unlocked by the Central Door Locking System
SEALANTS
Code No.2004: P/W (AS) Sensor fail (earth)
DIAGNOSIS TROUBLESHOOTING FLOW
REMOVAL AND INSTALLATION
Inspection Procedure B-1: Power Windows do not Work at All.
Code No.1001: P/W (DR) SW pulse1 disconnection
SERVICE SPECIFICATIONS
SEALANT
Code No.3004: P/W (RL) Sensor fail (earth)
POWER WINDOW TIMER FUNCTION CHECK
REMOVAL AND INSTALLATION
Inspection Procedure 2: Any of The Rear Panel Power Window Switch Position is defective.
Code No.4004: P/W (RR) Sensor fail (earth)
GLASS SLIDING MECHANISM CHECK AND ADJUSTMENT
SERVICE SPECIFICATIONS
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
INSPECTION
SPECIAL TOOL
SUNROOF OPERATION CHECK
SPECIAL TOOL
Inspection Procedure B-10: The Window Glass Lowers Automatically while it is Rising.
TROUBLE SYMPTOM CHART
Inspection Procedure A-2: Keyless Entry Hazard Lamp Answerback Function or the Room Lamp Answerback Function does not Work Normally.
Code No.2005: P/W (AS) 3 Times jam-protection
REMOVAL AND INSTALLATION
Code No.1004: P/W (DR) Sensor fail (earth)
SPECIAL TOOLS
CENTRAL DOOR LOCKING SYSTEM INSPECTION
REAR SLIDE WINDOW GLASS ADJUSTMENT
Inspection Procedure B-2: Driver’s Power Window does not Work by means of the Power Window Main Switch.
Code No.1001: P/W (DR) SW pulse1 disconnection
REMOVAL AND INSTALLATION
LUBRICANT
REAR BODY
Code No.1002: P/W (DR) SW pulse2 disconnection
Code No.4002 P/W (RR) SW pulse 2 disconnection
GENERAL INFORMATION
REMOVAL AND INSTALLATION
WINDOW GLASS REGULATOR
Code No.4001: P/W (RR) SW pulse1 disconnection
Code No.1004: P/W (DR) Sensor fail (earth)
BODY PANELLING
SUNROOF SAFETY FUNCTION CHECK
Inspection procedure B-7: Power Window Timer Function does not Work Normally.
Code No.1002: P/W (DR) SW pulse2 disconnection
Code No.2008: P/W (AS) Parameter read failCode No.2009: P/W (AS) Position read fail
FRONT DOOR WINDOW GLASS ADJUSTMENT
Inspection Procedure B-6: Front Passenger’s and /or Rear Power Window do not Work by means of the Power Window Main Switch.
ADJUSTMENT OF ALIGNMENT OF HOOD STEPPED PORTION AND HOOD STRIKER
REMOVAL AND INSTALLATION
Inspection Procedure B-3: Driver’s Power Window does not Work by means of the Power Window Main Switch.
REMOVAL AND INSTALLATION
DIAGNOSIS TROUBLESHOOTING FLOW
BODY COLOUR CHARTS
Code No.4003: P/W (RR) Above window position
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
TROUBLE SYMPTOM CHART
SUNROOF FIT ADJUSTMENT
WINDOW GLASS
Code No. 5008: P/W (RP) Parameter read fail, Code No. 5009: P/W (RP) Position read fail
SPECIAL TOOL
DOOR OUTSIDE HANDLE PLAY CHECK
REAR PANEL POWER WINDOW INITIAL SET
POWER WINDOW SAFETY MECHANISM CHECK
Inspection Procedure A-1: Keyless Entry System does not Work at all.
REAR PANEL POWER WINDOW
INSPECTION
CHECK CHART FOR TROUBLE SYMPTOMS
Code No.2001: P/W (AS) SW pulse1 disconnection
Inspection Procedure A-1: Central Door Locking System does not Work at all.
POWER WINDOW CHECK
Code No.2003: P/W (AS) Above window position
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
DISASSEMBLY AND REASSEMBLY
SUNROOF
GENERAL INFORMATION
DOOR INSIDE HANDLE PLAY ADJUSTMENT
Code No.3001: P/W (RL) SW pulse1 disconnection
POWER WINDOW RELAY CHECK
REMOVAL AND INSTALLATION
Code No.3003: P/W (RL) Above window position
SUNROOF LID GLASS OPERATION CURRENT CHECK
KEYLESS ENTRY SYSTEM TIMER LOCK FUNCTION INSPECTION
DIAGNOSIS TROUBLESHOOTING FLOW
Code No.1008: P/W (DR) Parameter read failCode No.1009: P/W (DR) Position read fail
POWER WINDOW OPERATING CURRENT CHECK
SERVICE SPECIFICATIONS
Inspection Procedure B-4: Relevant Power Window(s) do not Work by means of the Front Passenger’s Power Window Sub Switch and Rear Power Window Sub Switches.
INPUT SIGNAL CHART
Inspection Procedure A-3: Encrypted Code cannot be Registered.
Code No. 5002: P/W (RP) SW pulse 2 disconnection
Code No.4008: P/W (RR) Parameter read failCode No.4009: P/W (RR) Position read fail
CUSTOMISE FUNCTION
DIAGNOSIS CODE CHART
REAR SEAT
PASSENGER’S AIR BAG CUT OFF INDICATOR LAMP CHECK
Code No.B1431: Side-airbag module (LH) (squib) system (open-circuited in the squib circuit)
PASSENGER’S (FRONT) AIR BAG MODULE
Code No.B1477: Power supply voltage (IG1 (B) voltage) drops abnormally.
INSTRUMENT PANEL AND FLOOR CONSOLE
Code No.B1422: Side-airbag module (RH) (squib) system (short-circuited to the earth)
Code No.B1423: Side-airbag module (RH) (squib) system (short-circuited to the power supply)
Code No.B1428: Side impact sensor (RH) communication errorCode No.B1429: Side impact sensor (RH) communication impossible
REMOVAL AND INSTALLATION
Code No.B1610: Seat belt pre-tensioner (passenger’s side) (squib) system (open-circuited in the squib circuit)
Code No.B1509: Incorrect installation of SRS-ECU
Code No.B1443: Curtain air bag module (RH) (squib) system (short-circuited to the power supply)
REMOVAL AND INSTALLATION
INSIDE REAR VIEW MIRROR
SERVICE PRECAUTIONS
Code No.B1410: Passenger’s (front) air bag module (squib) system (short-circuited between terminals of the squib circuit)
Code No.B1402: Driver’s air bag module (squib) system (short-circuited to the earth)
INSPECTION
INSPECTION
CHECK CHART FOR TROUBLE SYMPTOMS
DRIVER’S AIR BAG MODULE
REMOVAL AND INSTALLATION
SRS AIR BAG SPECIAL CONNECTOR
Code No.B1595: Front impact sensor RH system (short circuit in the sensor)Code No.B1596: Front impact sensor RH system (open circuit in the sensor)Code No.B1597: Front impact sensor RH (short circuited in the earth)Code No.B1598: Front impact sensor RH (short circuited in the power supply)Code No.B1599: Front impact sensor LH system (short circuit in the sensor)Code No.B1600: Front impact sensor LH (open circuit in the sensor)Code No.B1601: Front impact sensor LH (short circuited in the earth)Code No.B1602: Front impact sensor LH (short circuited in the power supply)
DISASSEMBLY AND REASSEMBLY
FRONT AIR BAG AND SEAT BELT WITH PRE-TENSIONER
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
INSPECTION
SEAT BELT WITH PRE-TENSIONER
REMOVAL AND INSTALLATION
DISASSEMBLY AND REASSEMBLY
Code No. B1551: SRS warning lamp circuit malfunction (Lamp does not Illuminate).
Code No.B1476: Power supply voltage (IG1 (A) voltage) drops abnormally.
CHECK CHART FOR DIAGNOSIS CODES
REMOVAL AND INSTALLATION
INSPECTION
Code No.B1611: Seat belt pre-tensioner (passenger’s side) (squib) system (short-circuited to the earth)
Code No.B1413: Passenger’s (front) air bag module (squib) system (short-circuited to the power supply)
Code No.B1430: Side-airbag module (LH) (squib) system (short-circuited between terminals of the squib circuit)
Code No.B1412: Passenger’s (front) air bag module (squib) system (short-circuited to the earth)
Code No.B1451: Curtain air bag module (LH) (squib) system (open-circuited in the squib circuit)
Code No.B1604: Seat belt pre-tensioner (driver’s side) (squib) system (open-circuited in the squib circuit)
REMOVAL AND INSTALLATION
Code No.B1605: Seat belt pre-tensioner (driver’s side) (squib) system (short-circuited to the earth)
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Code No.B1411: Passenger’s (front) air bag module (squib) system (open-circuited in the squib circuit)
Code No.B1606: Seat belt pre-tensioner (driver’s side) (squib) system (short-circuited to the power supply)
SIDE IMPACT SENSOR
Inspection Procedure 1: Communication with M.U.T.-III is not possible (Communication is not possible with SRS).
INSPECTION
Code No.B1402: Driver’s air bag module (squib) system (short-circuited to the earth)
Code No.B1606: Seat belt pre-tensioner (driver’s side) (squib) system (short-circuited to the power supply)
REMOVAL AND INSTALLATION
WARNING/CAUTION LABELS
Code No.B1437: Side impact sensor (LH) voltage error
SPECIAL TOOLS
Code No.B1433: Side-airbag module (LH) (squib) system (short-circuited to the power supply)
FRONT SEAT
GENERAL INFORMATION
Code No.B1400: Driver’s air bag module (squib) system (short-circuited between terminals of the squib circuit)
Inspection Procedure 1: Communication with M.U.T.-III is not possible (Communication is not possible with SRS).
Code No.B1427: Side impact sensor (RH) voltage error
POST-COLLISION DIAGNOSIS
SRS WARNING LAMP CHECK
INSPECTION
Code No.B1519: SRS-ECU connector lock out of order
Code No.B1404: Driver’s air bag module (squib ignition drive circuit) system detected short circuitCode No.B1405: Driver’s air bag module (squib ignition drive circuit) system detected open circuitCode No.B1414: Passenger’s (front) air bag module (squib ignition drive circuit) system detected short circuitCode No.B1415: Passenger’s (front) air bag module (squib ignition drive circuit) system detected open circuitCode No.B1424: Side-airbag module (RH) (squib ignition drive circuit) system detected short circuitCode No.B1425: Side-airbag module (RH) (squib ignition drive circuit) system detected open circuitCode No.B1434: Side-airbag module (LH) (squib ignition drive circuit) system detected short circuitCode No.B1435: Side-airbag module (LH) (squib ignition drive circuit) system detected open circuitCode No.B1444: Curtain air bag module (RH) (squib ignition drive circuit) system detected short circuitCode No.B1445: Curtain air bag module (RH) (squib ignition drive circuit) system detected open circuitCode No.B1454: Curtain air bag module (LH) (squib ignition drive circuit) system detected short circuitCode No.B1455: Curtain air bag module (LH) (squib ignition drive circuit) system detected open circuitCode No.B1466: Analogue G-sensor system in the SRS-ECU (front air bag)Code No.B1467: Safing G-sensor open circuit (front air bag)Code No.B1468: Safing G-sensor short circuit (front air bag)Code No.B1469: Analogue G-sensor system in the SRS-ECU (side air bag)Code No.B1478: SRS-ECU capacitor circuit voltage too highCode No.B1479: SRS-ECU capacitor circuit voltage too lowCode No.B1496: SRS-ECU non-volatile memory (EEPROM)Code No.B1497: SRS-ECU application specific integrated circuit (for frontal activation)Code No.B1498: SRS-ECU ROM or RAM Code No.B1499: Collision decisionCode No.B1550: SRS warning lamp drive circuit malfunctionCode No.B1557: SRS-ECU application specific integrated circuitCode No.B1607: Seat belt pre-tensioner (driver’s side) (squib ignition drive circuit) system detected short circuitCode No.B1608: Seat belt pre-tensioner (driver’s side) (squib ignition drive circuit) system detected open circuitCode No.B1613: Seat belt pre-tensioner (passenger’s side) (squib ignition drive circuit) system detected short circuitCode No.B1614: Seat belt pre-tensioner (passenger’s side) (squib ignition drive circuit) system detected open circuit
Code No.B1452: Curtain air bag module (LH) (squib) system (short-circuited to the earth)
DIAGNOSIS FUNCTION
Code No.B1401: Driver’s air bag module (squib) system (open-circuited in the squib circuit)
INDIVIDUAL COMPONENT SERVICE
INSPECTION
Code No.B1609: Seat belt pre-tensioner (passenger’s side) (squib) system (short-circuit between terminals of the squib circuit)
SIDE-AIR BAG MODULE
Code No.B1604: Seat belt pre-tensioner (driver’s side) (squib) system (open-circuited in the squib circuit)
Code No.B1450: Curtain air bag module (LH) (squib) system (short-circuited between terminals of the squib circuit)
Code No. B1551: SRS warning lamp circuit malfunction (Lamp does not Illuminate).
INSPECTION
Code No.B1440: Curtain air bag module (RH) (squib) system (short-circuited between terminals of the squib circuit)
Code No.B1595: Front impact sensor RH system (short circuit in the sensor)Code No.B1596: Front impact sensor RH system (open circuit in the sensor)Code No.B1597: Front impact sensor RH (short circuited in the earth)Code No.B1598: Front impact sensor RH (short circuited in the power supply)Code No.B1599: Front impact sensor LH system (short circuit in the sensor)Code No.B1600: Front impact sensor LH (open circuit in the sensor)Code No.B1601: Front impact sensor LH (short circuited in the earth)Code No.B1602: Front impact sensor LH (short circuited in the power supply)
Code No.B1477: Power supply voltage (IG1 (B) voltage) drops abnormally.
CURTAIN AIR BAG MODULE
SRS-ECU
Code No.B1410: Passenger’s (front) air bag module (squib) system (short-circuited between terminals of the squib circuit)
INSPECTION
DOOR TRIM
Code No.B1612: Seat belt pre-tensioner (passenger’s side) (squib) system (short-circuited to the power supply)
PASSENGER’S AIR BAG CUT OFF SWITCH
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
Code No.B1609: Seat belt pre-tensioner (passenger’s side) (squib) system (short-circuit between terminals of the squib circuit)
Code No.B1404: Driver’s air bag module (squib ignition drive circuit) system detected short circuitCode No.B1405: Driver’s air bag module (squib ignition drive circuit) system detected open circuitCode No.B1414: Passenger’s (front) air bag module (squib ignition drive circuit) system detected short circuitCode No.B1415: Passenger’s (front) air bag module (squib ignition drive circuit) system detected open circuitCode No.B1466: Analogue G-sensor system in the SRS-ECUCode No.B1467: Safing G-sensor open circuitCode No.B1468: Safing G-sensor short circuitCode No.B1478: SRS-ECU capacitor circuit voltage too highCode No.B1479: SRS-ECU capacitor circuit voltage too lowCode No.B1496: SRS-ECU non-volatile memory (EEPROM)Code No.B1497: SRS-ECU application specific integrated circuit (for frontal activation)Code No.B1498: SRS-ECU ROM or RAMCode No.B1499: Collision decisionCode No.B1550: SRS warning lamp drive circuit malfunctionCode No.B1557: SRS-ECU application specific integrated circuitCode No.B1607: Seat belt pre-tensioner (driver’s side) (squib ignition drive circuit) system detected short circuitCode No.B1608: Seat belt pre-tensioner (driver’s side) (squib ignition drive circuit) system detected open circuitCode No.B1613: Seat belt pre-tensioner (passenger’s side) (squib ignition drive circuit) system detected short circuitCode No.B1614: Seat belt pre-tensioner (passenger’s side) (squib ignition drive circuit) system detected open circuit
Code No.B1420: Side-airbag module (RH) (squib) system (short-circuited between terminals of the squib circuit)
Code No.B1400: Driver’s air bag module (squib) system (short-circuited between terminals of the squib circuit)
Code No.B1551: SRS warning lamp circuit malfunction (Lamp does not Switch Off).
Code No.B1403: Driver’s air bag module (squib) system (short-circuited to the power supply)
INTERIOR TRIM
Code No.B1421: Side-airbag module (RH) (squib) system (open-circuited in the squib circuit)
Code No.B1509: Incorrect installation of SRS-ECU
Code No.B1611: Seat belt pre-tensioner (passenger’s side) (squib) system (short-circuited to the earth)
INSPECTION
Code No.B1403: Driver’s air bag module (squib) system (short-circuited to the power supply)
Code No.B1453: Curtain air bag module (LH) (squib) system (short-circuited to the power supply)
REMOVAL AND INSTALLATION
GENERAL INFORMATION
Code No.B1413: Passenger’s (front) air bag module (squib) system (short-circuited to the power supply)
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Code No.B1438: Side impact sensor (LH) communication errorCode No.B1439: Side impact sensor (LH) communication impossible
Code No.B1612: Seat belt pre-tensioner (passenger’s side) (squib) system (short-circuited to the power supply)
REMOVAL AND INSTALLATION
Code No.B1605: Seat belt pre-tensioner (driver’s side) (squib) system (short-circuited to the earth)
Code No.B1442: Curtain air bag module (RH) (squib) system (short-circuited to the earth)
Code No.B1401: Driver’s air bag module (squib) system (open-circuited in the squib circuit)
SIDE AND CURTAIN AIR BAGS
Code No.B1603: Seat belt pre-tensioner (driver’s side) (squib) system (short-circuited between terminals of the squib circuit)
GENERAL INFORMATION
REMOVAL AND INSTALLATION
HEADLINING
Code No.B1610: Seat belt pre-tensioner (passenger’s side) (squib) system (open-circuited in the squib circuit)
DISASSEMBLY AND REASSEMBLY
Code No.B1412: Passenger’s (front) air bag module (squib) system (short-circuited to the earth)
REMOVAL AND INSTALLATION
SPECIAL TOOL
REMOVAL AND INSTALLATION
Code No.B1603: Seat belt pre-tensioner (driver’s side) (squib) system (short-circuited between terminals of the squib circuit)
DIAGNOSIS TROUBLESHOOTING FLOW
SEAT BELT
Code No.B1411: Passenger’s (front) air bag module (squib) system (open-circuited in the squib circuit)
REMOVAL AND INSTALLATION
Code No.B1426: G-sensor of side impact sensor (RH) failureCode No.B1436: G-sensor of side impact sensor (LH) failure
FRONT IMPACT SENSOR
TEST EQUIPMENTS
Code No.B1476: Power supply voltage (IG1 (A) voltage) drops abnormally.
REMOVAL AND INSTALLATION
Code No.B1551: SRS warning lamp circuit malfunction (Lamp does not Switch Off).
Code No.B1432: Side-airbag module (LH) (squib) system (short-circuited to the earth)
Code No.B1519: SRS-ECU connector lock out of order
REMOVAL AND INSTALLATION
Code No.B1441: Curtain air bag module (RH) (squib) system (open-circuited in the squib circuit)
CHECK AT ENGINE-ECU TERMINAL
VACUUM HOSE PIPING DIAGRAM
DIAGNOSIS TROUBLESHOOTING FLOW
COMPONENT LOCATION
GENERAL INFORMATION
Inspection Procedure 5: Cruise Control cannot be Set (No Response when the "COAST/SET" Switch and the "ACC/RES" Switch is Pushed).
REMOVAL AND INSTALLATION
CONSTRUCTION AND OPERATION
Inspection Procedure 7: When the "ON/OFF" Switch is Turned ON, the Cruise Control Indicator Lamp does not Illuminate (However, the Cruise Control System is Normal).
CRUISE CONTROL SWITCH CHECK
FORCIBLE DPF REGENERATION
CHECK CHART FOR TROUBLE SYMPTOMS
VACUUM HOSE INSTALLATION
ACCELERATOR SYSTEM
EGR VALVE (DC MOTOR) CHECK
Code No.P1564: Abnormal voltage at cruise control switch
No. 2 EXHAUST GAS TEMPERATURE SENSOR (CATALYST TEMPERATURE) CHECK
SERVICE SPECIFICATIONS
REMOVAL AND INSTALLATION
CHECK CHART FOR DIAGNOSIS CODES
Inspection Procedure 6: Hunting (Repeated Acceleration and Deceleration) Occurs at the Set Vehicle Speed.
CRANK ANGLE SENSOR CHECK
GENERAL INFORMATION
Inspection Procedure 3: When the Selector Lever is Set to "N" Position, Cruise Control is not Cancelled .
EXHAUST GAS RECIRCULATION (EGR) SYSTEM
REMOVAL AND INSTALLATION
VACUUM HOSE CHECK
No. 1 EXHAUST GAS TEMPERATURE SENSOR CHECK
INTAKE AIR TEMPERATURE SENSOR CHECK
Inspection Procedure 2: When the Clutch Pedal is Depressed, Cruise Control is not Cancelled
REMOVAL AND INSTALLATION
No. 3 EXHAUST GAS TEMPERATURE SENSOR (DPF TEMPERATURE) CHECK
CHECK AT THE ECU TERMINALS
ENGINE COOLANT TEMPERATURE SENSOR CHECK
AIR FLOW SENSOR CHECK
DATA LIST REFERENCE TABLE
GENERAL INFORMATION
CHECK AT THE ECU TERMINALS
GENERAL INFORMATION
SPECIAL TOOLS
DIAGNOSIS FUNCTION
COMPONENT LOCATION (DPF SYSTEM)
CRUISE CONTROL SYSTEM COMPONENT CHECK
Inspection Procedure 1: When the Brake Pedal is Depressed, Cruise Control is not Cancelled.
GENERAL INFORMATION (DIESEL PARTICULATE FILTER SYSTEM)
Inspection Procedure 4: When the "CANCEL" Switch is Pushed, Cruise Control is not Cancelled.
EGR GAS TEMPERATURE SENSOR CHECK
REMOVAL AND INSTALLATION
GENERAL INFORMATION (EGR SYSTEM)
REMOVAL AND INSTALLATION
Code No.P1571: Malfunction of the stop lamp switch
VACUUM CIRCUIT DIAGRAM
REMOVAL AND INSTALLATION
PARKING BRAKE SWITCH CHECK
SERVICE SPECIFICATIONS
PARKING BRAKE PULL ROD STROKE ADJUSTMENT
REMOVAL AND INSTALLATION
PARKING BRAKE SWITCH CHECK
GENERAL INFORMATION
REMOVAL AND INSTALLATION
GENERAL INFORMATION
PARKING BRAKE LEVER STROKE CHECK AND ADJUSTMENT
REMOVAL AND INSTALLATION
INSPECTION TERMINAL LOCATION
ECU
EARTH CABLE
SENSOR
FUSIBLE LINK AND FUSE
EARTH
SOLENOID VALVE
RELAY
Code No.U1510: Power window sub switch (RL) time-out
SEALANT
GENERAL INFORMATION
DIAGNOSIS TROUBLESHOOTING FLOW
REMOVAL AND INSTALLATION
ETACS-ECU FUNCTIONS AND CONTROLS
Code No.U1509: Power window sub switch (AS) time-out
LIGHTING CONTROL SENSOR (LAMP SENSOR) CHECK
REMOVAL AND INSTALLATION
SPECIAL TOOLS
HORN RELAY CONTINUITY CHECK
CUSTOMISATION FUNCTION
SPEAKER TEST
SPECIAL TOOLS
REPLACEMENT OF REPLACEABLE BULB
Inspection Procedure 1: The RV meter does not show any information.
CAN BUS DIAGNOSTICS TABLE
Inspection Procedure 7: Voice guide "Unable to obtain vehicle speed. Please try again or contact your dealer for service" is sent from the speaker.
DIAGNOSIS MODE
DIAGNOSIS TROUBLESHOOTING FLOW
REMOVAL AND INSTALLATION
Code No.B1766: Transponder registered for other vehicle
Code No.U1530: Column-ECU checksum error
SPECIAL TOOL
Inspection Procedure 5: The radio broadcasting can not be received.
TROUBLE SYMPTOM CHART
DIAGNOSTIC FUNCTION
Inspection Procedure C-4: The hazard warning lamp switch signal is not received.
SPECIAL TOOLS
CHECK CHART FOR TROUBLE SYMPTOMS
TROUBLE SYMPTOM CHART
Code No.L0434 RLS rain sensor errorCode No.L0436 RLS light sensor error
TROUBLE SYMPTOM CHART
REMOVAL AND INSTALLATION
DIAGNOSIS CODE CHART
BATTERY CURRENT SENSOR CHECK
Code No.B1761: Chassis No. not recorded
DATA LIST REFERENCE TABLE
REMOVAL AND INSTALLATION
Inspection Procedure 1: Check the hands free ECU power supply circuit.
Inspection Procedure 19: Sound quality is poor.
Inspection Procedure 2: No sound is heard.
REMOVAL AND INSTALLATION
DIAGNOSIS CODE CHART
Inspection procedure 14: The seat belt warning lamp does not illuminate or flash.
REMOVAL AND INSTALLATION
Code No.U1532: LIN comm. lighting control sensor
DIAGNOSIS CODE CHART
Code No.U1150: Vehicle speed failure information
TROUBLESHOOTING
ERROR MESSAGE
INTRODUCTION TO AUDIO SYSTEM DIAGNOSIS
Code No.B1763: Column switch abnormality (Lighting switch)Code No.B1764: Column switch abnormality (Wiper/washer switch)
LIGHTING CONTROL SENSOR REMOVAL AND INSTALLATION
DATA LIST REFERENCE TABLE
Code No.U1100: Engine-ECU time-out (Related to Engine)Code No.U1101: A/T-ECU time-out (Related to A/T)
WINDSHIELD WIPER AND WASHER SWITCH CONTINUITY CHECK
Code No.U1073: Bus off
MICROPHONE UNIT REMOVAL AND INSTALLATION
PRECAUTIONS ON SERVICING MMCS
SPECIAL TOOLS
HOW TO SET THE COMPASS
GENERAL INFORMATION
Inspection Procedure 3: The high-beam and low-beam headlamps do not illuminate when the passing switch is operated.
REMOVAL AND INSTALLATION
SPECIAL TOOLS
Inspection Procedure 1: None of the low-beam headlamps illuminate.
Inspection Procedure 6: GPS signal cannot be received.
Inspection Procedure 6: Steering wheel voice control switch illumination does not come on.
SPECIAL TOOL
CUSTOMISATION FUNCTION
Inspection Procedure 4: The sound of external input are not played.
Code No.U1536: Power window sub switch (RL) checksum error
SELF-DIAGNOSIS
DIAGNOSIS CODE REFERENCE TABLE
FRONT FOG LAMP RELAY CONTINUITY CHECK
Inspection Procedure 1: The interior lamps (front room lamp, rear room lamp and ignition key cylinder illumination lamp) does not illuminate or extinguish normally.
TROUBLE SYMPTOM CHART
Inspection Procedure 11: There is noise but no reception for LW/MW/FM or no sound from LW/MW/FM.
The USB memory device data cannot be replayed.
GENERAL INFORMATION
Code No. B1731: Communication error with the engine-ECU
Code No.U1504: Lighting control sensor LIN timeout
SYMPTOM CHART
CUSTOMISE FUNCTION
REMOVAL AND INSTALLATION
Inspection Procedure 12: Poor reception.
Inspection Procedure C-2: The ignition switch (ACC) signal is not received.
Code No.U1508: Power window main switch time-out
DIAGNOSIS FUNCTION
DATA LIST REFERENCE TABLE
CHECK AT ECU TERMINALS
GENERAL INFORMATION
Diagnosis Item 5: Diagnose when the M.U.T.-III cannot receive the data sent by ETACS-ECU.
REMOVAL AND INSTALLATION
Code No.U1111: RV Meter time-out
Inspection Procedure 7: Broadcasts can be heard but both LW/MW/FM have a lot of noise.
HEADLAMP AUTOMATIC-SHUTDOWN FUNCTION CHECK
CHECK AT ECU TERMINAL
Inspection Procedure 1: The front fog lamps do not illuminate normally.
REMOVAL AND INSTALLATION
Inspection Procedure 1: Steering wheel audio remote control switch does not function.
SPECIAL TOOLS
Inspection Procedure 1: No navigation screen is displayed.
Diagnosis Item 4: Diagnose the terminator resistors
Inspection Procedure 6: The radio and CD player information is not displayed normally.
Inspection Procedure 14: Using the auto select function, too few automatic stations are selected.
Inspection Procedure 2: The USB memory device data cannot be replayed.
Inspection Procedure 7: Broadcasts can be heard but both AM and FM have a lot of noise.
Inspection Procedure 8: None of the turn-signal lamps illuminate.
CHECK AT ECU TERMINAL
Inspection Procedure 2: Steering wheel audio remote control switch illumination does not come on.
Code No.U1512: Rear panel power window-ECU time-out
REMOVAL AND INSTALLATION
GENERAL INFORMATION
Diagnosis Item 11: Diagnose the lines between the joint connectors (CAN1 and CAN2)
REMOVAL AND INSTALLATION
GENERAL INFORMATION
IGNITION SWITCH CONTINUITY CHECK
TROUBLE SYMPTOM CHART
Code No. B1760: Variant coding unmatched
Inspection Procedure 2: The engine does not start (cranking occurs but initial combustion does not).
SPECIAL TOOLS
ENGLISH SELECTION USING AUDIO SYSTEM
Inspection Procedure 9: The comfort flasher does not work normally.
GENERAL INFORMATION
TROUBLE SYMPTOM CHART
Inspection Procedure 3: No sound is heard from one of the speakers.
Diagnosis Item 10: Diagnose when the M.U.T.-III cannot receive the data sent by A/C-ECU.
Inspection Procedure 3: The rear room lamp does not illuminate normally.
HEADLAMP AUTO LAMP FUNCTION CHECK
Inspection Procedure 20: CD can not be ejected.
REMOVAL AND INSTALLATION
Inspection Procedure 5: Noise appears at certain places when travelling.
INSPECTION
Inspection Procedure 12: The turn-signal lamp indicator does not illuminate.
FUEL GAUGE UNIT CHECK
DIAGNOSTIC FUNCTION
Inspection Procedure 3: No sound is heard from one of the speaker.
HEADLAMP REMOVAL AND INSTALLATION
Inspection Procedure 1: The ignition key cannot be registered with the M.U.T.-III.
Inspection Procedure 6: Tachometer does not work (Other meters work).
CHARGING
Inspection Procedure 18: CD sound skips.
Diagnosis Item 9: Diagnose when the M.U.T.-III cannot receive the data sent by G and yaw rate sensor.
Code No.B1702: Reception error of key ID
Inspection Procedure 1: None of the tail lamps, position lamps and licence plate lamps illuminate.
Diagnosis Item 13: Diagnose when the M.U.T.-III cannot receive the data sent by engine-ECU.
Inspection Procedure 7: Daytime running lamp function does not work normally.
Diagnosis Item 7: Diagnose when the M.U.T.-III cannot receive the data sent by ABS-ECU
Inspection Procedure 3: No sound is heard from one of the speakers.
DIAGNOSIS TROUBLESHOOTING FLOW
SPECIAL TOOLS
VEHICLE MAGNETIC COMPENSATION
CHECK CHART FOR TROUBLE SYMPTOMS
Inspection Procedure 4: The freeze mark does not illuminate or flash normally. The freeze warning buzzer does not sound.
Diagnosis Item 1: Diagnose shorts in the power supply to CAN bus line
Inspection Procedure 8: SD card cannot be read.
GENERAL INFORMATION
ACCESSORY SOCKET RELAY CHECK
GENERAL INFORMATION
Inspection Procedure 3: The ambient air temperature is not displayed normally.
SPECIAL TOOLS
Inspection Procedure 2: The drive information is not displayed normally.
SPECIAL TOOLS
Inspection Procedure 4: When the speech switch is pressed, the voice information is not output.
Inspection Procedure 13: Distortion on LW/MW/FM.
Inspection Procedure 5: The compass does not indicate normally.
PAIRING A DEVICE OR DELETING A DEVICE
GENERAL INFORMATION
Diagnosis Item 2: Diagnose shorts in the earth to CAN bus line
Inspection Procedure 7: Fuel gauge does not work (Other meters work).
SERVICE MODE
ERASE THE PASSWORD
EXPLANATION ABOUT THE M.U.T.-III CAN BUS DIAGNOSTICS
Code No.U1534: Power window main switch checksum error
STRUCTURE
DIAGNOSIS TROUBLESHOOTING FLOW
FLUID LEVEL AND SPECIFIC GRAVITY CHECK
DIAGNOSIS TROUBLESHOOTING FLOW
FRONT FOG LAMP AIMING
DIAGNOSIS MODE
DIAGNOSIS TROUBLESHOOTING FLOW
Inspection Procedure 11: The rear fog lamp indicator does not illuminate.
Inspection procedure B-1: Lamp reminder buzzer function does not work normally.
DIAGNOSTIC FUNCTION
Inspection Procedure 2: Malfunction of the ignition switch power supply system
Code No.U1500: Column-ECU time-out
AUDIO ADAPTER INSPECTION
Diagnosis Item 12: Diagnose when the M.U.T.-III cannot receive the data sent by A/T-ECU.
DIAGNOSIS TROUBLESHOOTING FLOW
REMOVAL AND INSTALLATION
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
Inspection Procedure 8: There is noise when starting the engine.
PRINTED HEATER LINES CHECK
SERVICE SPECIFICATIONS
TROUBLE SYMPTOM CHART
DIAGNOSIS CODE TABLE
Inspection Procedure C-1: The column switch (lighting and wiper switch) signal is not received.
SPECIAL TOOLS
GENERAL INFORMATION
GENERAL INFORMATION
BATTERY TEST
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
Inspection Procedure 2: One of tail lamps does not illuminate.
SYSTEM OPERATION
Diagnosis Item 8: Diagnose when the M.U.T.-III cannot receive the data sent by steering wheel sensor.
Inspection procedure B-3: Door ajar warning buzzer function does not work normally.
DIAGNOSIS TROUBLESHOOTING FLOW
INTERIOR LAMPS
SPECIAL TOOLS
DIAGNOSIS CODE CHART
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
HAZARD WARNING LAMP SWITCH CHECK
REMOVAL AND INSTALLATION
HEADLAMP RELAY CHECK
REMOVAL AND INSTALLATION
SERVICE PRECAUTIONS
COLUMN SWITCH (SWITCH BODY) CONTINUITY CHECK
HANDS FREE ECU REMOVAL AND INSTALLATION
Code No.U1110: A/C-ECU timeout
GENERAL INFORMATION
Code No. 29: No receive fault detect signal
Inspection Procedure C-6: The seat belt switch signal is not received.
Inspection Procedure 8: Engine coolant temperature gauge does not work (Other meters work).
GENERAL INFORMATION
TEST EQUIPMENT
REMOVAL AND INSTALLATION
GENERAL INFORMATION
Code No.U1102: ABS-ECU or ASTC-ECU timeout
Inspection Procedure 6: Mixed with noise, only at night.
Inspection Procedure 6: The headlamp automatic-shutdown function does not work normally.
GENERAL INFORMATION
CHECK CHART FOR TROUBLE SYMPTOMS
Inspection Procedure 1: The hazard warning lamps do not illuminate.
DIAGNOSIS TROUBLESHOOTING FLOW
DIAGNOSIS MODE
REMOVAL AND INSTALLATION
Inspection Procedure 10: The auto lamp function does not work normally.
ETACS-ECU FUNCTIONS AND CONTROLS
SPECIAL TOOLS
KEY REMINDER SWITCH CONTINUITY CHECK
Inspection Procedure 2: One of the front fog lamps does not illuminate normally.
DATA LIST REFERENCE TABLE
Code No.U1570 No bus activity error for LIN
Inspection Procedure 2: No sound is heard.
SERVICE SPECIFICATIONS
TROUBLESHOOTING
LUMINOUS INTENSITY MEASUREMENT
Inspection Procedure 5: One of the headlamps does not illuminate. <4-bulb type>
SERVICE SPECIFICATION
REMOVAL AND INSTALLATION
GENERAL INFORMATION
PAIRING A DEVICE OR DELETING A DEVICE
CHECK ETACS-ECU (IMMOBILIZER-ECU)
CHART CLASSIFIED BY DIAGNOSIS CODES
GENERAL INFORMATION
Inspection Procedure 4: The screen is not normal in the navigation mode. (The own vehicle mark is dislocated.)
HOW TO REGISTER ENCRYPTED CODE
Inspection Procedure C-3: The ignition switch (IG1) signal is not received.
Inspection Procedure 5: Speedometer does not work (Other meters work).
SPECIAL TOOL
TROUBLE SYMPTOM CHART
Inspection Procedure 2: The front room lamp does not illuminate normally.
PRECAUTIONS ON HOW TO REPAIR THE CAN BUS LINES
DIAGNOSIS TROUBLESHOOTING FLOW
DIAGNOSIS TROUBLESHOOTING FLOW
GENERAL INFORMATION
Inspection Procedure 1: Power supply circuit system check.Inspection Procedure 2: Odometer and trip meter is not displayed.inspection procedure 3: No needle meters work.Inspection Procedure 4: If the ignition switch is turned to the ON position, the indicator and warning lamps do not illuminate.
REMOVAL AND INSTALLATION
Inspection Procedure 4: One of position lamps or licence plate lamps does not illuminate.
REPLACEMENT OF REPLACEABLE BULB
CAN COMMUNICATION-RELATED DIAGNOSIS CODE (U CODE) TABLE
Code No.L0432 RLS RS adaptation error
Inspection Procedure 16: CD can not be inserted.
EXTERIOR LAMPS
SPECIAL TOOLS
REAR WINDOW DEFOGGER RELAY CHECK
DIAGNOSIS MODE
Inspection procedure 13: The door-ajar warning lamp does not illuminate.
DIAGNOSIS CODE CHART
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
CIGARETTE LIGHTER CHECK
REMOVAL AND INSTALLATION
SPECIAL TOOL
Inspection Procedure 15: Preset station are erased.
SPECIAL TOOLS
SPECIAL TOOLS
Inspection Procedure 11: There is noise but no reception for both AM and FM or no sound from AM, or no sound from FM.
Inspection Procedure 2: No sound is heard.
CHECK TROUBLE BY USING THE INPUT SIGNAL CHECK
Code No.B1762: Ignition OFF current draw (IOD) fuse disconnectedCode No.B1765: ECU power supply fuse disconnected
Code No.B1707: Detection of turn-signal lamp (open circuit)
Inspection Procedure A-1: When the ignition switch is at the "LOCK" (OFF) position, the functions do not work normally. Check the battery power supply circuit to the ETACS-ECU.
Inspection Procedure 1: The ignition key cylinder illumination lamp does not illuminate normally.
DIAGNOSIS TROUBLESHOOTING FLOW
GENERAL
SERVICE MODE
TACHOMETER CHECK
SPECIAL TOOLS
Inspection Procedure 7: CD cannot be played.
MAIN UNIT TERMINAL VOLTAGE
Inspection Procedure 2: The USB memory device data cannot be replayed.
GENERAL INFORMATION
Inspection Procedure 3: No sound is heard from one of the speakers.
SERVICE SPECIFICATIONS
Code No.U1537: Power window sub switch (RR) checksum error
TROUBLE SYMPTOM CHART
TROUBLE SYMPTOM CHART
Inspection Procedure 5: One of the headlamps does not illuminate. <2-bulb type>
The USB memory device data cannot be replayed.
SYSTEM OPERATION
Inspection Procedure 9: The high-beam indicator does not illuminate.
REMOVAL AND INSTALLATION
CAN-RELATED CONNECTOR POSITION
Inspection Procedure 2: No sound is heard.
DIAGNOSIS CODE CHART
Inspection Procedure 5: DIAGNOSIS MODE cannot be made an entry.
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
TROUBLE SYMPTOM CHART
GENERAL INFORMATION
Code No.U1535: Power window sub switch (AS) checksum error
Code No. 19: ETACS CAN Timeout
Inspection Procedure 9: Some noise appears when there is vibration or shocks during travelling.
Code No. B1722: Transponder antenna failure
Inspection procedure C-5: One of the door switch signals is not received.
Inspection Procedure 3: When the speech switch is pressed, the voice information is output, but the voice recognition is not performed.
Code No. 26: Engine CAN Timeout
SPECIAL TOOLS
CUSTOMISE FUNCTION
Inspection Procedure 17: No sound. (CD only)
REMOVAL AND INSTALLATION
Inspection Procedure 1: Steering wheel audio remote control switch does not function.
GENERAL INFORMATION
GENERAL INFORMATION
Code No.U1511: Power window sub switch (RR) time-out
Diagnosis Item 3: Diagnose shorts between CAN_H and L lines
GENERAL INFORMATION
GENERAL INFORMATION
Code No.U1507: ETACS-ECU LIN Communication Error
REAR FOG LAMP RELAY CONTINUITY CHECK
Inspection Procedure 10: The front fog lamp indicator does not illuminate.
CAN BUS DIAGNOSTICS
Inspection Procedure B-4: Seat belt warning buzzer function does not work normally.
DIAGNOSIS CODE CHART
Inspection Procedure 1: Power of radio and CD player does not turn ON when the ignition switch is in the "ACC" position or "ON" position.
INTRODUCTION TO DIAGNOSIS
REMOVAL AND INSTALLATION
CHECK THE SPEEDOMETER
Code No. B1709: ETACS-ECU internal error (EEPROM abnormality)
ETACS-ECU FUNCTIONS AND CONTROLS
AMBIENT AIR TEMPERATURE SENSOR INSPECTION
Code No.U1538: Rear panel power window-ECU checksum error
Inspection procedure B-2: Turn-signal lamp operation sound function does not work normally.
HEADLAMP LEVELLING SWITCH CHECK
STEERING WHEEL AUDIO REMOTE CONTROL SWITCH INSPECTION
TROUBLE SYMPTOM CHART
Inspection Procedure 3: The ambient air temperature is not displayed normally.
STRUCTURE
DIAGNOSTIC FUNCTION
REMOVAL AND INSTALLATION
GENERAL INFORMATION
Diagnosis Item 6: Diagnose when the M.U.T.-III cannot receive the data sent by RV meter
Inspection Procedure 1: The rear fog lamp do not illuminate normally.
CUSTOMISATION FUNCTION
GENERAL INFORMATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Inspection Procedure 10: Ever-present noise.
Code No.B1703: Key ID inconsistent
ENGINE COOLANT TEMPERATURE GAUGE UNIT CHECK
HEADLAMP AIMING
Inspection Procedure 2: None of the high-beam headlamps illuminate.
WASTE GATE ACTUATOR CHECK
SERVICE SPECIFICATIONS
GENERAL INFORMATION
REMOVAL AND INSTALLATION
AIR DUCT AND AIR CLEANER
SPECIAL TOOLS
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
VARIABLE GEOMETRY ACTUATOR CHECK
VARIABLE GEOMETRY SOLENOID VALVE CHECK
EXHAUST PIPE AND MUFFLER
REMOVAL AND INSTALLATION
TURBOCHARGER SUPERCHARGING PRESSURE CHECK
REMOVAL AND INSTALLATION
INTAKE MANIFOLD
INTERCOOLER
INSPECTION
INSPECTION
REMOVAL AND INSTALLATION
EXHAUST MANIFOLD
UNDERCOAT APPLICATION LOCATIONS
BODY SEALING LOCATIONS
ANTICORROSION PRIMER LOCATIONS
ANTICORROSION PRIMER LOCATIONS
UNDERCOAT APPLICATION LOCATIONS
BODY SEALING LOCATIONS
UNDERBODY ANTICORROSION AGENT LOCATIONS
BODY SEALING LOCATIONS
ANTICORROSION PRIMER LOCATIONS
UNDERCOAT APPLICATION LOCATIONS
AXLE SHAFT AXIAL PLAY ADJUSTMENT
DISASSEMBLY AND REASSEMBLY
SERVICE SPECIFICATIONS
HUB BOLT REPLACEMENT
GEAR OIL LEVEL CHECK
REASSEMBLY
INSPECTION
REAR DIFFERENTIAL LOCK AIR PUMP CHECK
REAR DIFFERENTIAL LOCK SYSTEM AIR LEAKAGE CHECK <4WD>
GENERAL INFORMATION
REMOVAL AND INSTALLATION
SPECIAL TOOLS
DIFFERENTIAL
REMOVAL AND INSTALLATION
GENERAL INFORMATION
REAR DIFFERENTIAL LOCK-ECU CHECK
REMOVAL AND INSTALLATION
GEAR OIL REPLACEMENT
DISASSEMBLY
DESCRIPTION OF CONSTRUCTION AND OPERATION
DIFFERENTIAL CASE DISASSEMBLY AND REASSEMBLY <5A/T or EXCEPT 4WD WITH HIGH POWER ENGINE>
REAR DIFFERENTIAL LOCK DETECTION SWITCH CHECK <4WD>
INSPECTION
LUBRICANTS
AXLE SHAFT AXIAL PLAY CHECK
REAR AXLE TOTAL BACKLASH CHECK
REAR DIFFERENTIAL LOCK DETECTION SWITCH CHECK
SEALANT AND ADHESIVE
REMOVAL AND INSTALLATION
LUBRICANT
CONCENTRATION MEASUREMENT
ENGINE COOLANT REPLACEMENT
GENERAL INFORMATION
REMOVAL AND INSTALLATION
INSPECTION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
GENERAL INFORMATION
REMOVAL AND INSTALLATION
WATER PUMP COOLANT LEAK CHECK
RADIATOR CAP VALVE OPENING PRESSURE CHECK
SERVICE SPECIFICATIONS
ENGINE COOLANT LEAK CHECK
INSPECTION
SPECIAL TOOLS
WATER PASSAGE
REMOVAL AND INSTALLATION
SEALANTS
GENERAL SPECIFICATIONS
REMOVAL AND INSTALLATION <2WD>
LUBRICANTS
4LLc SWITCH CONTINUITY CHECK
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
INSPECTION
SERVICE SPECIFICATIONS
INSPECTION
REMOVAL AND INSTALLATION <4WD>
4WD OPERATION DETECTION SWITCH CONTINUITY CHECK
REMOVAL AND INSTALLATION
INSPECTION
4WD SYSTEM
SERVICE SPECIFICATIONS
GENERAL INFORMATION
DISASSEMBLY AND REASSEMBLY
INSPECTION
GENERAL SPECIFICATIONS
INSPECTION
DISASSEMBLY AND REASSEMBLY
ADJUSTMENT OF TRANSFER
2WD/4WD DETECTION SWITCH CONTINUITY CHECK
SPECIAL TOOLS
4WD DETECTION SWITCH CONTINUITY CHECK
TRANSFER OIL REPLACEMENT
INSPECTION
GENERAL INFORMATION
GENERAL INFORMATION
TORQUE SPECIFICATIONS
LUBRICANTS
INSPECTION
DISASSEMBLY AND REASSEMBLY
INSPECTION
TORQUE SPECIFICATIONS
INSPECTION
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
TRANSMISSION OIL LEVEL CHECK
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
TRANSFER OIL LEVEL CHECK
DISASSEMBLY AND REASSEMBLY
REMOVAL AND INSTALLATION
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
TRANSMISSION OIL REPLACEMENT
INSPECTION
SEALANTS
CENTRE DIFFERENTIAL LOCK DETECTION SWITCH CONTINUITY CHECK
INSPECTION
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
SNAP RING, SPACER AND THRUST PLATE FOR ADJUSTMENT
HIGH/LOW DETECTION SWITCH CONTINUITY CHECK
LUBRICANT
SPECIAL TOOLS
SEALANTS
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
CENTRE DIFFERENTIAL LOCK OPERATION DETECTION SWITCH CONTINUITY CHECK
GENERAL INFORMATION
HIGH/LOW DETECTION SWITCH CONTINUITY CHECK
SNAP RING, SPACER AND THRUST PLATE FOR ADJUSTMENT
SEALANTS
DISASSEMBLY AND REASSEMBLY
WIRING DIAGRAM
CUSTOMISATION FUNCTION
INSPECTION
Inspection Procedure 6: The rain sensitive AUTO wiper function does not work at all
OVERFENDER
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
INSPECTION
Inspection Procedure 5: The Intermittent Wiper Interval is not Changed According to The Vehicle Speed.
FRONT DECK GARNISH
REMOVAL AND INSTALLATION
BUMPER AND RADIATOR GRILLE
Inspection Procedure: The headlamp washer does not work.
REMOVAL AND INSTALLATION
SERVICE SPECIFICATION
SPECIAL TOOL
LUBRICANT
Inspection Procedure 4: The Intermittent Wiper Interval cannot be Adjusted by Operating The Windshield Intermittent Wiper Volume Control.
ADHESIVE
DIAGNOSIS TROUBLESHOOTING FLOW
Inspection Procedure 3: The Windshield Wipers do not Stop at The Specified Park Position
WINDSHIELD INTERMITTENT WIPER INSPECTION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
INSPECTION
DISASSEMBLY AND REASSEMBLY
HEADLAMP WASHER
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
SERVICE SPECIFICATION
TROUBLE SYMPTOM CHART
INSPECTION
REMOVAL AND INSTALLATION
AERO PARTS
Inspection Procedure 2: The Windshield Wipers do not Work Normally.
SPECIAL TOOLS
REMOVAL AND INSTALLATION
REAR GUARD BAR REMOVAL AND INSTALLATION
ROOF DRIP MOULDING REMOVAL AND INSTALLATION
LIGHTING CONTROL SENSOR REMOVAL AND INSTALLATION
SPECIAL TOOL
INSPECTION PROCEDURE 8: Sometimes the rain sensitive AUTO wiper function works even though there is no rainfall
INSPECTION PROCEDURE 2: Right or Left Heated Door Mirror does not Operate
LIGHTING CONTROL SENSOR (RAIN SENSOR) INSPECTION
Lighting control sensor (rain sensor) adaptation
GENERAL INFORMATION
REMOVAL AND INSTALLATION
SIDE STEP
Inspection Procedure 1: All Heated Door Mirrors do not Operate
DISASSEMBLY AND REASSEMBLY
ADHESIVE
SPECIAL TOOL
Inspection Procedure 9: The Windshield Washer does not Work Normally.
DISASSEMBLY AND REASSEMBLY
DIAGNOSIS TROUBLESHOOTING FLOW
WINDSHIELD WIPER AND WASHER
ADHESIVE
LUBRICANT
DATA LIST REFERENCE TABLE
REMOVAL AND INSTALLATION
Inspection Procedure 1: The windshield wipers do not work at all.
INSPECTION PROCEDURE 7: The rain sensitive AUTO wiper function works even though there is no rainfall
REMOVAL AND INSTALLATION
ADHESIVE
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
ADHESIVE
TROUBLE SYMPTOM CHART
DIAGNOSIS TROUBLESHOOTING FLOW
OUTSIDE MIRROR
CUSTOMISATION FUNCTION
REMOVAL AND INSTALLATION
SPECIAL TOOLS
FLUID REPLACEMENT
LUBRICANTS
STEERING WHEEL RETURN TO CENTRE CHECK
STEERING WHEEL
GENERAL INFORMATION
REMOVAL AND INSTALLATION
TIE ROD END BALL JOINT DUST COVER CHECK
STEERING WHEEL FREE PLAY CHECK
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
FLUID LEVEL CHECK
SERVICE SPECIFICATIONS
OIL PUMP
REMOVAL AND INSTALLATION
DISASSEMBLY AND REASSEMBLY
TIE ROD END BALL JOINT STARTING TORQUE CHECK
DISASSEMBLY AND REASSEMBLY
INSPECTION
STEERING COLUMN SHAFT ASSEMBLY SHOCK ABSORBING MECHANISM CHECK
OIL RESERVOIR
SEALANTS
DRIVE BELT TENSION CHECK
STEERING SHAFT AND COLUMN
INSPECTION
REMOVAL AND INSTALLATION
POWER STEERING PRESSURE SWITCH CHECK
OIL PUMP PRESSURE TEST
STEERING ANGLE CHECK
POWER STEERING SYSTEM AIR BLEEDING
GENERAL INFORMATION
DISASSEMBLY AND REASSEMBLY
STEERING GEAR
INSPECTION
STATIONARY STEERING EFFORT CHECK
URETHANE FOAM USAGE LOCATIONS
SILENCER APPLICATION LOCATIONS
CARRIER
DASH PANEL
CARRIER
FRONT FLOOR
SILENCER APPLICATION LOCATIONS
SILENCER APPLICATION LOCATIONS
FRONT FLOOR
FENDER SHIELD
URETHANE FOAM USAGE LOCATIONS
HEADLAMP SUPPORT
REAR END PANEL
SIDE STRUCTURE
ROOF
REAR END PANEL
SIDE STRUCTURE
BODY MAIN CROSS-SECTIONAL VIEWS
SIDE STRUCTURE
CARRIER
MAINTENANCE AND SERVICEABILITY
REAR END PANEL
REAR FLOOR
FRONT FLOOR
CARRIER
MAINTENANCE AND SERVICEABILITY
ROOF
REAR FLOOR
BODY MAIN CROSS-SECTIONAL VIEWS
BODY COMPONENTS
FRONT DECK
FRONT DOOR
REAR DOOR
BODY MAIN CROSS-SECTIONAL VIEWS
URETHANE FOAM USAGE LOCATIONS
MAINTENANCE AND SERVICEABILITY
BODY COMPONENTS
ROOF
BODY COMPONENTS
INITIALIZATION PROCEDURE FOR LEARNING VALUE IN DIESEL PARTICULATE FILTER (DPF) SYSTEM
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE
HOW TO TREAT PAST TROUBLE
PASSIVE SAFETY
SPACIOUS CABIN
HOW TO READ CIRCUIT DIAGRAMS
SUPPLY PUMP CORRECTION LEARNING PROCEDURE
HOW TO USE THIS MANUAL
There is no applicable page.
MAJOR SPECIFICATIONS
VEHICLES WITH SEMI AUTOMATIC AIR CONDITIONER STARTING
SRS SERVICE PRECAUTIONS
PRE-INSPECTION CONDITION
VEHICLE IDENTIFICATION NUMBER
VEHICLE WASHING
MAJOR SPECIFICATIONS
BATTERY CURRENT SENSOR CALIBRATION
WIRE COLOUR CODE
MODELS
DIAGNOSIS FUNCTION
HOW TO USE THE INSPECTION PROCEDURES
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
ABBREVIATION SYMBOLS
TARGETS OF DEVELOPMENT
INTERIOR
GENERAL DATA AND SPECIFICATIONS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AND SEAT BELT WITH PRE-TENSIONER
SUSPENSION
MANUFACTURER PLATE
IN ORDER TO PREVENT VEHICLES FROM FIRE
ENGINE MODEL STAMPING
INTERIOR
ENVIRONMENTAL PROTECTION
EXTERIOR
ENGINE OILS
SUPPORT LOCATIONS FOR LIFTING AND JACKING
ACTIVE SAFETY
HOW TO SHIFT LOCK FORCED RELEASE
INTERIOR
OTHER EQUIPMENTS
PRODUCT FEATURES
SMALL INJECTION QUANTITY LEARNING PROCEDURE
VEHICLE IDENTIFICATION
INSPECTION SERVICE POINTS FOR A BLOWN FUSE
CONNECTOR INSPECTION SERVICE POINTS
CONNECTOR MEASUREMENT SERVICE POINTS
CONTENTS OF TROUBLESHOOTING
SERVICING ELECTRICAL SYSTEM
GENERAL DATA AND SPECIFICATIONS
SERVICING COMMON RAIL ENGINE
HOW TO PERFORM CHASSIS NUMBER (CHASSIS NO.) WRITING
COMPOSITION AND CONTENTS OF WIRING DIAGRAMS
VEHICLE IDENTIFICATION
HOW TO READ CONFIGURATION DIAGRAMS
MARKINGS FOR CONNECTOR AND EARTHING
MULTI USE TESTER (M.U.T.-III) SUB ASSEMBLY
INJECTOR IDENTIFICATION CODE REGISTRATION PROCEDURE
WHAT THE COMMON RAIL ENGINE LEARNS
HOW TO USE THIS MANUAL
TRANSMISSION
PRECAUTIONS FOR INSTALLATION OF ON-VEHICLE RADIO TRANSMISSION EQUIPMENT
VEHICLE INFORMATION CODE PLATE
HOW TO USE THE THROTTLE CONTROLLER
APPLICATION OF ANTI-CORROSION AGENTS AND UNDERCOATS
BRAKE
SERVICEABILITY AND RELIABILITY
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
ENGINE
STEERING
WHEELHOUSE
RADIATOR GRILLE
BODY COLOUR CHARTS
FRONT END
WHEELHOUSE
BODY COLOUR CODE
WHEELHOUSE
INSTRUMENT PANEL
DOOR
OVERALL CONFIGURATION DIAGRAM
FLOOR AND ROOF
FRAME
TRANSMISSION <2WD>
DOOR
FRAME <2WD EXCEPT HIGH RIDER>
ENGINE COMPARTMENT <4D5-DOHC (LHD)>
TRANSMISSION <4WD>
INSTRUMENT PANEL
OVERALL CONFIGURATION DIAGRAM
ENGINE COMPARTMENT
FLOOR AND ROOF
FLOOR AND ROOF
REMOVAL AND INSTALLATION <2WD (EXCEPT HIGH RIDER)>
GENERAL INFORMATION
ALTERNATOR AND POWER STEERING OIL PUMP DRIVE BELT TENSION CHECK
REMOVAL AND INSTALLATION
VALVE CLEARANCE CHECK AND ADJUSTMENT
REMOVAL AND INSTALLATION
GENERAL SPECIFICATIONS
REWORK DIMENSIONS
TORQUE SPECIFICATIONS
INSPECTION
REMOVAL AND INSTALLATION
SEALANTS
GENERAL INFORMATION
REMOVAL AND INSTALLATION
A/C COMPRESSOR DRIVE BELT TENSION CHECK AND ADJUSTMENT
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
INSPECTION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
SERVICE SPECIFICATIONS
INSPECTION
REMOVAL AND INSTALLATION
BASE ENGINE
REMOVAL AND INSTALLATION
INSPECTION
AUTO-TENSIONER CHECK
SEALANTS
SERVICE SPECIFICATIONS
SPECIAL TOOLS
REMOVAL AND INSTALLATION
IDLE SPEED CHECK
TIMING BELT B TENSION ADJUSTMENT
INSPECTION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION <2WD (HIGH RIDER) AND 4WD>
INSPECTION
REMOVAL AND INSTALLATION
SPECIAL TOOLS
COMPRESSION PRESSURE CHECK
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
INSPECTION
REMOVAL AND INSTALLATION
SERVICE SPECIFICATION
LUBRICATION SYSTEM
REMOVAL AND INSTALLATION
OIL PRESSURE CHECK
SEALANT
SPECIAL TOOLS
GENERAL INFORMATION
REMOVAL AND INSTALLATION
LUBRICANT
OIL PASSAGE
ENGINE OIL CHECK
ENGINE OIL FILTER REPLACEMENT
ENGINE OIL REPLACEMENT
QUARTER, INNER
No.5 CROSSMEMBER
FRONT PILLAR
HEADLAMP SUPPORT
QUARTER OUTER
SIDE GATE PANEL
FRONT DOOR OUTER PANEL (ADHESION TYPE)
REAR PILLAR INNER
FRONT PILLAR
REAR DOOR OUTER PANEL (WELDED TYPE)
FENDER SHIELD
SIDE SILL
ROOF
CENTRE PILLAR
FRONT DOOR OUTER PANEL (WELDED TYPE)
SIDE GATE PANEL
REAR END SILL
SIDE SILL
SIDE SILL
No.1 CROSSMEMBER
REAR PILLAR OUTER
REAR DOOR OUTER PANEL (ADHESION TYPE)
REAR PILLAR INNER
ROOF
REAR PILLAR OUTER
FRONT DOOR OUTER PANEL (ADHESION TYPE)
FRONT DOOR OUTER PANEL (WELDED TYPE)
ROOF
SIDE GATE PANEL
SIDE GATE PANEL
DIAGNOSIS
SPECIFICATIONS
INSTALLATION SERVICE POINT
TYRE INFLATION PRESSURE CHECK
WHEEL BALANCE ACCURACY
GENERAL INFORMATION
WHEEL RUNOUT CHECK
TYRE WEAR CHECK
SERVICE SPECIFICATIONS
REMOVAL AND INSTALLATION
FRONT WHEEL ALIGNMENT CHECK AND ADJUSTMENT
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - AIR BAG
OVERFENDER
HOOD
REAR GATE PANEL FIT ADJUSTMENT
ADJUSTMENT OF FUEL FILLER LID FIT
FOG LAMP AIMING
DOOR
HEADLAMP AIMING
ADJUSTMENT OF FUEL FILLER LID FIT
REMOVAL AND INSTALLATION
SPECIAL TOOLS
INSPECTION
SERVICE SPECIFICATIONS
GENERAL INFORMATION
DISASSEMBLY AND REASSEMBLY
GENERAL INFORMATION
LUBRICANT
PROPELLER SHAFT UNIVERSAL JOINT CHECK
SERVICE SPECIFICATIONS
WHEEL BEARING AXIAL PLAY CHECK
REMOVAL AND INSTALLATION <2WD (EXCEPT HIGH RIDER)>
REMOVAL AND INSTALLATION
DISASSEMBLY
HUB BOLT REPLACEMENT
DISASSEMBLY AND REASSEMBLY <2WD (EXCEPT HIGH RIDER)>
SPECIAL TOOLS
KNUCKLE DISASSEMBLY AND REASSEMBLY
REMOVAL AND INSTALLATION
INSPECTION
GEAR OIL REPLACEMENT <4WD>
GENERAL INFORMATION
FRONT AXLE GEAR OIL LEVEL CHECK <4WD>
REMOVAL AND INSTALLATION <2WD (HIGH RIDER), 4WD>
INSPECTION
DESCRIPTION OF CONSTRUCTION AND OPERATION
FREE WHEEL CLUTCH DISASSEMBLY AND REASSEMBLY
LUBRICANTS
BJ BOOT (RESIN BOOT) REPLACEMENT
FREE WHEEL SOLENOID VALVE OPERATION CHECK <4WD: VEHICLES FOR EUROPE (EXCEPT FOR RUSSIA)>
DISASSEMBLY AND REASSEMBLY
SEALANT AND ADHESIVE <4WD>
DIFFERENTIAL MOUNTING INSULATOR REPLACEMENT
INSPECTION
REMOVAL AND INSTALLATION
GENERAL INFORMATION
FRONT AXLE TOTAL BACKLASH CHECK <4WD>
GENERAL INFORMATION
REASSEMBLY
INSPECTION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
DIFFERENTIAL MOUNT
DIFFERENTIAL
DISASSEMBLY AND REASSEMBLY
INSPECTION
LUBRICANTS
CLUTCH SWITCH CONTINUITY CHECK
REMOVAL AND INSTALLATION
INSPECTION
SERVICE SPECIFICATIONS
LUBRICANTS
CLUTCH PEDAL CHECK AND ADJUSTMENT
GENERAL INFORMATION
TORQUE SPECIFICATIONS
SERVICE SPECIFICATIONS
DISASSEMBLY AND REASSEMBLY
GENERAL INFORMATION
INSPECTION
DISASSEMBLY AND REASSEMBLY
REMOVAL AND INSTALLATION
GENERAL SPECIFICATIONS
INSPECTION
REMOVAL AND INSTALLATION
DISASSEMBLY AND REASSEMBLY
CLUTCH BLEEDING
J/C
SHIFT LOCK AND KEY INTERLOCK MECHANISM
ACCESSORY SOCKET
CENTRAL DOOR LOCKING SYSTEM
ELC-5A/T
REAR FOG LAMP
AUTOMATIC AIR CONDITIONER
CHARGING SYSTEM
SUPER SELECT 4WD SYSTEM
CENTRAL DOOR LOCKING SYSTEM
ABS AND ASTC
IMMOBILIZER SYSTEM
HEATED SEAT
EASY SELECT 4WD SYSTEM
HEATER
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
HEADLAMP
CHARGING SYSTEM
BACK-UP LAMP
RADIO AND CD PLAYER
WINDSHIELD WIPER AND WASHER
MANUAL AIR CONDITIONER
HEADLAMP MANUAL LEVELLING SYSTEM
STOP LAMP
METER AND GAUGE
BACK-UP LAMP
RV METER
METER AND GAUGE
ENGINE CONTROL SYSTEM
ELC-4A/T
SRS
ABS
J/C
REAR WINDOW DEFOGGER AND HEATED DOOR MIRROR
POWER DISTRIBUTION SYSTEM
HEADLAMP
ELC-5A/T
SPARE CONNECTOR (FOR AUDIO)
OIL PRESSURE WARNING LAMP, FUEL FILTER WARNING LAMP, FUEL WARNING LAMP AND BRAKE WARNING LAMP
HEADLAMP MANUAL LEVELLING SYSTEM
STOP LAMP
ABS AND ASTC
POWER SEAT
CENTRALIZED JUNCTION
RADIO AND CD PLAYER
TAIL LAMP, POSITION LAMP, LICENCE PLATE LAMP AND LIGHTING MONITOR BUZZER
TURN-SIGNAL LAMP AND HAZARD WARNING LAMP
ROOM LAMP AND IGNITION KEY CYLINDER ILLUMINATION LAMP
CRUISE CONTROL SYSTEM
ABS
REAR FOG LAMP
SEAT BELT WARNING BUZZER
SUNROOF
STARTING SYSTEM
J/B
OIL PRESSURE WARNING LAMP, FUEL FILTER WARNING LAMP, FUEL WARNING LAMP AND BRAKE WARNING LAMP
HEADLAMP
IMMOBILIZER SYSTEM
POWER WINDOWS
HANDS-FREE INTERFACE SYSTEM
OIL PRESSURE WARNING LAMP, FUEL FILTER WARNING LAMP, FUEL WARNING LAMP AND BRAKE WARNING LAMP
GLOW SYSTEM
DOOR AJAR WARNING BUZZER
ELECTRIC RETRACTABLE REMOTE CONTROLLED MIRROR
REAR WINDOW DEFOGGER AND HEATED DOOR MIRROR
REAR DIFFERENTIAL LOCK SYSTEM
CENTRAL DOOR LOCKING SYSTEM
HEATED SEAT
REAR FOG LAMP
SEAT BELT WARNING BUZZER
TAIL LAMP, POSITION LAMP, LICENCE PLATE LAMP AND LIGHTING MONITOR BUZZER
WINDSHIELD WIPER AND WASHER
TAIL LAMP, POSITION LAMP, LICENCE PLATE LAMP AND LIGHTING MONITOR BUZZER
POWER DISTRIBUTION SYSTEM
POWER WINDOWS
USB BOX
AUTOMATIC AIR CONDITIONER
CAN
SPARE CONNECTOR (FOR TRAILER)
CRUISE CONTROL SYSTEM
FRONT FOG LAMP
ELECTRIC RETRACTABLE REMOTE CONTROLLED MIRROR
PTC HEATER
MANUAL AIR CONDITIONER
HEADLAMP MANUAL LEVELLING SYSTEM
HEADLAMP WASHER
CENTRAL DOOR LOCKING SYSTEM
DOOR COURTESY LAMP
SPARE CONNECTOR (FOR ACC SOCKET)
SRS
SRS
REAR WINDOW DEFOGGER AND HEATED DOOR MIRROR
SRS
REMOTE CONTROLLED MIRROR
DOOR AJAR WARNING BUZZER
DOOR COURTESY LAMP
CLOCK
REAR WINDOW DEFOGGER AND HEATED DOOR MIRROR
TAIL LAMP, POSITION LAMP, LICENCE PLATE LAMP AND LIGHTING MONITOR BUZZER
ENGINE CONTROL SYSTEM
ROOM LAMP AND IGNITION KEY CYLINDER ILLUMINATION LAMP
REAR FOG LAMP
TURN-SIGNAL LAMP AND HAZARD WARNING LAMP
CIGARETTE LIGHTER AND DOWN LAMP
GLOW SYSTEM
HORN
GLOVE BOX LAMP
SPARE CONNECTOR (FOR FRONT FOG LAMP)
LOCATION OF SYNTHETIC-RESIN PARTS
GENERAL INFORMATION
GENERAL INFORMATION
INSPECTION
REMOVAL AND INSTALLATION
Code No.C1361: Abnormal pressure sensor characteristics
HYDRAULIC UNIT CHECK
BRAKE FLUID LEVEL SENSOR CHECK
GENERAL INFORMATION
Code No.C1620: Engine-ECU communication error
INSPECTION CHART FOR TROUBLE SYMPTOMS
DISASSEMBLY AND REASSEMBLY <2WD (High rider), 4WD>
Inspection Procedure 1: Communication between M.U.T.-III and the ABS-ECU is not possible.
Inspection Procedure 3: Brake warning lamp stays ON with the parking brake lever or the parking brake stick released (ABS warning lamp is OFF).
Code No.C1207: Wheel speed sensor (FL) (malfunction power circuit)
Code No.C1205: Wheel speed sensor (FL) (signal open circuit)
DISASSEMBLY AND REASSEMBLY <2WD (except High rider)>
IN THE EVENT OF A DISCHARGED BATTERY
DIAGNOSIS FUNCTION
Code No.C1215: Wheel speed sensor (RL) (signal open circuit)
BRAKE LINING THICKNESS CHECK
Code No. C1381: G-sensor (output error, seizure)
WHEEL SPEED SENSOR OUTPUT CURRENT MEASUREMENT
GENERAL INFORMATION
REAR BRAKE
Code No.C1381: G-sensor malfunction (abnormal seizure or output error) <4WD>
SENSORS
SERVICE SPECIFICATIONS
REMOVAL AND INSTALLATION <2WD (except High rider)>
Code No.C1388: Yaw rate sensor (active check error)Code No.C1389: G-sensor (active check error)
Code No.C1396: Engine-ECU malfunction
Code No. C1371: Yaw rate sensor (output error, oscillation error, zero-point error)
Code No.U1101: A/T-ECU timeout error
Code No.U1190: ETACS signal receiving error
BRAKE DISC CHECK
Code No.C1340: Stop lamp switch circuit malfunction
ABS-ECU
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
SERVICE SPECIFICATIONS
Code No.C1201: Wheel speed sensor (FR) (signal short circuit)Code No.C1206: Wheel speed sensor (FL) (signal short circuit)Code No.C1211: Wheel speed sensor (RR) (signal short circuit)Code No.C1216: Wheel speed sensor (RL) (signal short circuit)
Inspection Procedure 2: ASTC OFF indicator lamp flashes at a rate of 2Hz
Code No.U1073: Trouble in CAN bus system
SPECIAL TOOLS
Inspection Procedure 2: The ABS warning lamp remains illuminated after the engine is started.
BRAKE LINING AND BRAKE DRUM CONTACT CHECK
GENERAL INFORMATION
STOP LAMP SWITCH CHECK
Code No.U1120: Engine malfunction detection
REMOVAL AND INSTALLATION
Code No.C1225: Wheel speed sensor malfunction (Abnormality in tyre size)
SYSTEM OPERATION
Code No.C1393: G rate sensor (zero-point not calibrated)
Code No.C1216: Wheel speed sensor (RL) (signal short circuit)
Code No.U1105: G and yaw rate sensor timeout error
BRAKE WARNING LAMP, ABS WARNING LAMP, ASTC INDICATOR LAMP, ASTC OFF INDICATOR LAMP INSPECTION
Code No.C1293: Abnormal rear differential lock detection circuit
CHECK CHART FOR TROUBLE SYMPTOMS
Inspection Procedure 6: ASTC OFF indicator lamp stays ON after the engine is started.
Code No.C1200: Wheel speed sensor (FR) (signal open circuit)
WHEEL SPEED SENSOR INSPECTION
Code No. C1340: Stop lamp switch malfunction
SERVICE SPECIFICATIONS
LOAD SENSING SPRING LENGTH CHECK AND ADJUSTMENT
Code No.C1226: Control solenoid valve (FR) pressure holding systemCode No.C1231: Control solenoid valve (FR) pressure reducing systemCode No.C1236: Control solenoid valve (FL) pressure holding systemCode No.C1241: Control solenoid valve (FL) pressure reducing systemCode No.C1246: Control solenoid valve (RR) pressure holding systemCode No.C1251: Control solenoid valve (RR) pressure reducing systemCode No.C1256: Control solenoid valve (RL) pressure holding systemCode No.C1261: Control solenoid valve (RL) pressure reducing systemCode No.C1278: Valve relay malfunction (open circuit)Code No.C1279: Valve relay malfunction (short circuit)
REMOVAL AND INSTALLATION
BRAKE DRUM INSIDE DIAMETER CHECK
Code No.C1505: Steering Wheel Sensor (Signal Seizure or Abnormal Neutral Point)Code No.C1506: Steering Wheel Sensor (Steering Wheel Sensor Malfunction)
LUBRICANTS
Code No.U1073: Bus-off
Code No.C1211: Wheel speed sensor (RR) (signal short circuit)
ABS WARNING LAMP AND BRAKE WARNING LAMP CHECK
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
NOTES WITH REGARD TO DIAGNOSIS
REMOVAL AND INSTALLATION
DATA LIST REFERENCE TABLE
ACTUATOR TEST REFERENCE TABLE
GENERAL INFORMATION
INSPECTION
DIAGNOSIS FUNCTION
Code No.C1225: Wheel Speed Sensor Malfunction (Abnormality in tyre size)
Code No.C1382: G-sensor malfunction (low voltage) <4WD>Code No.C1383: G-sensor malfunction (high voltage) <4WD>
MASTER CYLINDER
BRAKE PAD CHECK
Code No.U1201: Yaw rate sensor (parity error)Code No.U1202: G-sensor parity error
REMOVAL AND INSTALLATION
Code No.C1226: Control solenoid valve (FR) pressure holding systemCode No.C1236: Control solenoid valve (FL) pressure holding systemCode No.C1246: Control solenoid valve (RR) pressure holding systemCode No.C1256: Control solenoid valve (RL) pressure holding systemCode No.C1231: Control solenoid valve (FR) decompressing systemCode No.C1241: Control solenoid valve (FL) pressure reducing systemCode No.C1251: Control solenoid valve (RR) pressure reducing systemCode No.C1261: Control solenoid valve (RL) decompressing systemCode No.C1300: Linear valve (secondly)Code No.C1310: Linear valve (primary)
CHECK AT ASTC-ECU
G AND YAW RATE SENSOR CALIBRATION
Inspection Procedure 5: ASTC indicator lamp stays ON after the engine is started.
LOAD-SENSING PROPORTIONING VALVE FUNCTION TEST
REMOVAL AND INSTALLATION
FRONT BRAKE
Code No.C1201: Wheel speed sensor (FR) (signal short circuit)
GENERAL INFORMATION
Code No.C1266: Motor systemCode No.C1273: Motor relay (stuck off)Code No.C1274: Motor relay (stuck on)Code No.C1280: Motor fail-safe relay (short circuit)
Inspection Procedure 4: ABS warning lamp remains illuminated after the engine is started.
Code No.C1385: Yaw rate sensor (internal error)
Code No. C1395 Brake fluid charging incompletion
REMOVAL AND INSTALLATION
CHECK AT ABS-ECU
REMOVAL AND INSTALLATION
INSPECTION
DATA LIST REFERENCE TABLE
SPECIAL TOOLS
Code No.C1223: G and yaw rate sensor (active check error)
GENERAL INFORMATION
BRAKE DRAG FORCE CHECK
DATA LIST REFERENCE TABLE
Code No.C1362: Abnormal pressure sensor (output error, open or short circuit)
SENSORS
Code No.C1202: Wheel speed sensor (FR) (malfunction power circuit)
Inspection Procedure 1: M.U.T.-III cannot communicate only with ASTC-ECU.
REMOVAL AND INSTALLATION
ASTC-ECU
INSPECTION
HYDRAULIC UNIT CHECK
REMOVAL AND INSTALLATION
Inspection procedure 4: The initial check sound of hydraulic unit is loud.
Inspection Procedure 3: ABS system does not operate.
INSPECTION
Code No.C1266: Motor malfunction (motor stick or open circuit)Code No.C1273: Motor relay malfunction (open circuit)Code No.C1274: Motor relay malfunction (short circuit)
INSPECTION
INSPECTION CHART FOR DIAGNOSIS CODE
TROUBLE SYMPTOM CHART
INSPECTION
BRAKE PEDAL
Code No.U1200: Steering wheel sensor communication error
Code No. C1860: High voltage at ASTC-ECU power supply
Code No.C1394: Steering wheel sensor neutral point not learned
STEERING WHEEL SENSOR CALIBRATION
Code No.C1292: CAN communication error
Code No.C1210: Wheel speed sensor (RR) (signal open circuit)
BLEEDING
Code No.C1861: Low voltage at ASTC-ECU power supply
BRAKE LINE
BRAKE PAD REPLACEMENT
Code No.C1364: Pressure sensor malfunction
Code No.C1365: G-sensor malfunction (abnormal power supply) <4WD>
Code No.C1217: Wheel speed sensor (RL) (malfunction power circuit)
REMOVAL AND INSTALLATION <2WD (High rider), 4WD>
ACTUATORS
Code No.C1386: G-sensor (internal error)
ACTUATOR TEST REFERENCE TABLE
Code No.U1104: Steering wheel sensor timeout error
DISASSEMBLY AND REASSEMBLY <2WD (High rider), 4WD>
DIAGNOSIS CODE CHART
NOTES WITH REGARD TO DIAGNOSIS
Inspection procedure 9: The initial check sound of hydraulic unit is loud.
Code No.U1100: Engine-ECU timeout error
Code No. C1860: ABS-ECU power supply system malfunction (high voltage)
Code No.C1206: Wheel speed sensor (FL) (signal short circuit)
BRAKE PEDAL CHECK AND ADJUSTMENT
Code No. C1369: G and yaw rate sensor (bank run record)
Inspection Procedure 8: ASTC System dose not operate.
Code No.U1109: ETACS-ECU timeout error
REMOVAL AND INSTALLATION
Code No.U1204: Steering wheel sensor communication error
BRAKE BOOSTER OPERATING TEST
ACTUATORS
STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING
Code No.U1205: G and yaw rate sensor message counter error
Inspection Procedure 7: The ASTC system cannot be disabled when ASC OFF switch is pressed to turn the system OFF.
Code No.C1861: ABS-ECU power supply system malfunction (low voltage)
DISASSEMBLY AND REASSEMBLY <2WD (except High rider)>
Code No.C1291: Reverse signal (seizure)
REMOVAL AND INSTALLATION
Code No.C1278: Solenoid valve relay (open circuit)Code No.C1279: Solenoid valve relay (short circuit)
Code No.C1200: Wheel speed sensor (FR) (signal open circuit)Code No.C1205: Wheel speed sensor (FL) (signal open circuit)Code No.C1210: Wheel speed sensor (RR) (signal open circuit)Code No.C1215: Wheel speed sensor (RL) (signal open circuit)
INSPECTION
Code No.C1202: Wheel speed sensor (FR) (malfunction power circuit)Code No.C1207: Wheel speed sensor (FL) (malfunction power circuit)Code No.C1212: Wheel speed sensor (RR) (malfunction power circuit)Code No.C1217: Wheel speed sensor (RL) (malfunction power circuit)
ACTUATOR TEST TABLE
DIAGNOSIS CODE CHART
SPECIAL TOOLS
IN THE EVENT OF A DISCHARGED BATTERY
CHECK VALVE OPERATION CHECK
Code No.C1212: Wheel speed sensor (RR) (malfunction power circuit)
INSPECTION
WHEEL SPEED SENSOR OUTPUT CURRENT MEASUREMENT
Code No.P1790 Back up line system
Inspection Procedure 8: Shift Shock when Shifting from N to R and Long Delay
BRAKE
DISASSEMBLY AND REASSEMBLY
GENERAL INFORMATION
INHIBITOR SWITCH CONTINUITY CHECK
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
SNAP RING, SPACER, THRUST WASHER, THRUST RACE AND PRESSURE PLATE FOR ADJUSTMENT
TORQUE CONVERTER
LUBRICANTS
DISASSEMBLY AND REASSEMBLY
CONTROL UNIT
SERVICE SPECIFICATIONS
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
SEALANTS
4WD OPERATION DETECTION SWITCH CONTINUITY CHECK
Inspection Procedure 7: Shift Shock when Shifting from N to D and Long Delay
DISASSEMBLY AND REASSEMBLY
REMOVAL AND INSTALLATION <4A/T>
DISASSEMBLY AND REASSEMBLY
GENERAL SPECIFICATIONS
4WD DETECTION SWITCH CONTINUITY CHECK
DISASSEMBLY AND REASSEMBLY
SERVICE SPECIFICATION(S)
4LLc SWITCH CONTINUITY CHECK
TRANSFER OIL CHECK <4WD>
CLUTCH
DISASSEMBLY AND REASSEMBLY
HYDRAULIC PRESSURE TESTS
DISASSEMBLY AND REASSEMBLY
Inspection Procedure 14: Poor Acceleration
SEALANTS
DISASSEMBLY AND REASSEMBLY
Code No.P1767 (P0720) Output shaft speed sensor system
DIAGNOSTIC FUNCTION
Inspection Procedure 16: 4LLc operation detection switch system <4WD>
DISASSEMBLY AND REASSEMBLY
GENERAL INFORMATION
Inspection Procedure 4: Does not Move Backward
TRANSFER OIL REPLACEMENT <4WD>
DISASSEMBLY AND REASSEMBLY
GENERAL DESCRIPTION
SPECIAL TOOL(S)
OIL PUMP
A/T FLUID CHECK
Code No.P1773 (P0750) Low-reverse solenoid valve system
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
Inspection Procedure 15: Vibration
DISASSEMBLY AND REASSEMBLY
Code No.P1774 (P0755) Underdrive solenoid valve system
DISASSEMBLY AND REASSEMBLY
SERVICE SPECIFICATIONS
GENERAL SPECIFICATIONS
VALVE BODY SPRING IDENTIFICATION
Code No.P1770 (P0705) Inhibitor switch system <4A/T>
REMOVAL AND INSTALLATION
Code No.P1770 (P0705): Inhibitor switch system <5A/T>
Inspection Procedure 12: Does not Shift Properly (some Point)
DISASSEMBLY AND REASSEMBLY
GENERAL SPECIFICATIONS
DISASSEMBLY AND REASSEMBLY
SOLENOID VALVE CHECK
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
Inspection Procedure 11: Does not Shift Properly (all Points)
Code No.P1901: CAN signal time-out (Engine-ECU)
Code No.P1764 (P0710) A/T fluid temperature sensor system
HIGH/LOW DETECTION SWITCH CONTINUITY CHECK
Code No.U1190: Can’t receive fault detection control signal
INSPECTION
A/T CONTROL RELAY CHECK
SEALANTS AND ADHESIVES
DISASSEMBLY AND REASSEMBLY
VALVE BODY SPRING IDENTIFICATION
DISASSEMBLY AND REASSEMBLY
Inspection Procedure 19: Shift Lock Mechanism Does Not Work Normally.
GENERAL DESCRIPTION
Code No.P1776 (P0765) Overdrive solenoid valve system
CONTROLLER AREA NETWORK (CAN) COMMUNICATION
A/T FLUID COOLER
GENERAL
Code No.P1787 Damper clutch system (stuck on)
DAMPER CLUTCH CONTROL
DISASSEMBLY AND REASSEMBLY
ADJUSTMENT OF TRANSFER
Inspection Procedure 3: Does not Move Forward
SPECIAL TOOLS
INSPECTION
ACTUATOR TEST REFERENCE TABLE
SEALANTS
Code No.P1771 (P0705): Inhibitor switch system <5A/T>
Inspection Procedure 5: Does not Move (Forward or Backward)
SERVICE SPECIFICATIONS
KEY INTERLOCK AND SHIFT LOCK MECHANISM CHECK AND ADJUSTMENT
Inspection Procedure 10: Shift Shock and Slipping
Code No.P1788 (P1751) A/T control relay system
DISASSEMBLY AND REASSEMBLY
SPECIAL TOOLS
DISASSEMBLY AND REASSEMBLY
Code No.P1778 (P0740) Damper clutch control solenoid valve system
ROAD TEST
Code No.P1771 (P0705) Inhibitor switch system <4A/T>
DISASSEMBLY AND REASSEMBLY
Code No. U1102 ASTC-ECU time-out
EEPROM
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
A/T-ECU TERMINAL VOLTAGE REGERENCE CHART
Code No.U1073: Bus off
OSCILLOSCOPE CHECK PROCEDURE
Code No.P1779 (1st), P1780 (2nd), P1781 (3rd), P1782 (4th), P1783 (5th), P1784 (reverse): Gear incorrect ratio <5A/T>
DISASSEMBLY AND REASSEMBLY
INSPECTION
GENERAL INFORMATION
ADJUSTMENT OF TRANSFER
INSPECTION
DISASSEMBLY AND REASSEMBLY
ELECTRONIC CONTROL SYSTEM
DIAGNOSIS TROUBLESHOOTING FLOW
SHIFT PATTERN
TORQUE SPECIFICATIONS
Code No.P1766 (P0715) Input shaft speed sensor system
SPECIAL TOOLS
INHIBITOR SWITCH AND CONTROL CABLE ADJUSTMENT
Code No.P1775 (P0760) Second solenoid valve system
HYDRAULIC CIRCUIT
SHIFT PATTERN CONTROL
LINE PRESSURE ADJUSTMENT
A/T FLUID CHANGE
Code No.P1779 (1st), P1780 (2nd), P1781 (3rd), P1782 (4th), P1784 (reverse): Gear incorrect ratio <4A/T>
LUBRICANTS
DISASSEMBLY AND REASSEMBLY
POWER TRAIN
Inspection Procedure 2: Engine Does not Start
DISASSEMBLY AND REASSEMBLY
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION <5A/T>
DISASSEMBLY AND REASSEMBLY
GENERAL INFORMATION
DISASSEMBLY AND REASSEMBLY
SNAP RING, SPACER, THRUST RACE AND PRESSURE PLATE FOR ADJUSTMENT
Code No.U1100: Engine-ECU time-out (related to engine)
Code No.P1777 (P0770) Reduction solenoid valve system <5A/T>
Inspection Procedure 6: Engine Stalls During Shifting
DISASSEMBLY AND REASSEMBLY
FLUSHING COOLERS AND TUBES
DISASSEMBLY AND REASSEMBLY
SELECTOR LEVER OPERATION CHECK
GENERAL INFORMATION
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
VALVE BODY SPRING IDENTIFICATION
DISASSEMBLY AND REASSEMBLY
DISASSEMBLY AND REASSEMBLY
SPEEDOMETER GEAR
DISASSEMBLY AND REASSEMBLY
DATA LIST REFERENCE TABLE
A/T FLUID TEMPERATURE SENSOR CHECK
CENTRE DIFFERENTIAL LOCK DETECTION SWITCH CHECK
Code No.U1109: ETACS-ECU time-out
DISASSEMBLY AND REASSEMBLY
Inspection Procedure 9: Shift Shock when Shifting from N to D, N to R and Long Delay
OIL FILTER
MANUAL CONTROL SYSTEM
VALVE BODY
LUBRICANT(S)
2WD/4WD DETECTION SWITCH CHECK
A/T CONTROL COMPONENT LAYOUT
REMOVAL AND INSTALLATION
Inspection Procedure 17: Sport Mode System
TORQUE SPECIFICATIONS
TORQUE CONVERTER STALL CHECK
Inspection Procedure 13: Does not Shift (no Diagnosis Code)
DIAGNOSIS CODE CHART
DIAGNOSTIC FUNCTION
DISASSEMBLY AND REASSEMBLY
TORQUE SPECIFICATIONS
INHIBITOR SWITCH CHECK
DISASSEMBLY AND ASSEMBLY
CENTRE DIFFERENTIAL LOCK OPERATION DETECTION SWITCH CHECK
Code No.P1763 (P0710) A/T fluid temperature sensor system
DISASSEMBLY AND REASSEMBLY
TROUBLE SYMPTOMS CHART
REMOVAL AND INSTALLATION
Inspection Procedure 18: Key Interlock Mechanism Does Not Work Normally.
DISASSEMBLY AND REASSEMBLY
SNAP RING, SPACER, THRUST WASHER, THRUST RACE AND PRESSURE PLATE FOR ADJUSTMENT
DISASSEMBLY AND REASSEMBLY
Code No.P1786 Damper clutch system (stuck off)
Code No.U1120: Failure information of engine-ECU
HIGH/LOW DETECTION SWITCH CONTINUITY CHECK
LUBRICANTS
Inspection Procedure 1: Communication with the M.U.T.-III is not Possible.
REMOVAL AND INSTALLATION
STARTER MOTOR ASSEMBLY INSPECTION
SELF-REGULATING GLOW SYSTEM CHECK
GLOW CONTROL
SERVICE SPECIFICATION
STARTER RELAY CHECK
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
GENERAL INFORMATION
SERVICE SPECIFICATIONS
ENGINE COOLANT TEMPERATURE SENSOR CHECK
OUTPUT CURRENT TEST
REMOVAL AND INSTALLATION
GENERAL INFORMATION
WAVEFORM CHECK USING AN OSCILLOSCOPE
REGULATED VOLTAGE TEST
CHECK AT THE ECU TERMINALS
CHECK AT THE ECU TERMINALS
GLOW PLUG CHECK
SPECIAL TOOL
REMOVAL AND INSTALLATION
SERVICE SPECIFICATIONS
GLOW PLUG CHECK
REMOVAL AND INSTALLATION
GLOW PLUG RELAY CHECK
GENERAL INFORMATION
ALTERNATOR OUTPUT LINE VOLTAGE DROP TEST
REMOVAL AND INSTALLATION
GENERAL INFORMATION
GENERAL INFORMATION
INSPECTION
REMOVAL AND INSTALLATION
INSPECTION
INSPECTION
REMOVAL AND INSTALLATION
Inspection Procedure 2: The blower does not work
DIAGNOSIS TROUBLESHOOTING FLOW
REMOVAL AND INSTALLATION
Inspection Procedure 8: The PTC heater does not work
SPECIAL TOOL
COMPRESSOR NOISE CHECK
Code No.B1001,B1002: Interior temperature sensor system
HEATER UNIT
DUAL PRESSURE SWITCH CHECK
Inspection Procedure 3: The blower air volume cannot be changed
INSPECTION
Inspection Procedure 4: The A/C compressor and clutch assembly does not work
PERFORMANCE TEST
INSPECTION
CHECK AT A/C EVAPORATOR AIR OUTLET THERMISTOR TERMINALS
LUBRICANTS
Inspection Procedure 1: Cool air does not come
DISASSEMBLY AND REASSEMBLY
VENTILATION SYSTEM
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
SERVICE SPECIFICATIONS
Inspection Procedure 7: The PTC heater does not work
INSPECTION
Code No. B1021,B1022: Air Thermo Sensor system
A/C COMPRESSOR DRIVE BELT TENSION CHECK AND ADJUSTMENT
DISASSEMBLY AND REASSEMBLY
CHECK CHART FOR TROUBLE SYMPTOMS
Inspection Procedure 4: The inside/outside air changeover is impossible
CHECK THE REFRIGERANT LEVEL
Inspection Procedure 6: The Rear Window Defogger does not work
CHARGING AND DISCHARGING
REMOVAL AND INSTALLATION
A/C REFIGERANT CONDENSER ASSEMBLY
REMOVAL AND INSTALLATION
TROUBLE SYMPTOM CHART
REFILLING OF OIL IN THE A/C SYSTEM
Inspection Procedure 9: A/C-ECU power supply system
ACTUATOR TEST TABLE
REPLACE THE CLEAN AIR FILTER
INSPECTION
INSPECTION
DISASSEMBLY AND REASSEMBLY
DIAGNOSIS TROUBLESHOOTING FLOW
DISASSEMBLY AND REASSEMBLY
GENERAL INFORMATION
SERVICE DATA REFERENCE TABLE
Inspection Procedure 1: Cool air does not come
Inspection Procedure 5: The A/C compressor does not work
DUCT
DIAGNOSIS FUNCTION
Code No. B1011,B1012: Ambient temperature sensor system
Inspection Procedure 5: Condenser Fan does not Operate.
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
IDLE-UP OPERATION CHECK
A/C COMPRESSOR CLUTCH TEST
REMOVAL AND INSTALLATION
DIAGNOSIS CODE CHART
OTHER PARTS
Inspection Procedure 6: The rear window defogger does not work
REMOVAL AND INSTALLATION
SERVICE SPECIFICATIONS
INSPECTION
Code No.B1045: Motor drive system for the air mixing damper
RELAY CONTINUITY CHECK
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Inspection Procedure 2: The blower does not work
Code No.B1045: Motor drive system for the air mixing damper
TROUBLE SYMPTOM CHART
Inspection Procedure 9: The outlet air temperature can not be changed even if the amount of solar radiation changes
Code No.B1041,B1042: Potentiometer system for the air mixing damper
REMOVAL AND INSTALLATION
Inspection Procedure 7: The rear window defogger does not work
SPECIAL TOOL
Inspection Procedure 3: The blower air volume cannot be changed
A/C COMPRESSOR AND CLUTCH ASSEMBLY
Code No. B1065: Motor drive system for mode selection damper
A/C CONTROLLER
CHECK AT THE A/C-ECU TERMINALS
REMOVAL AND INSTALLATION
DISASSEMBLY AND REASSEMBLY
Code No. B1061,B1062: Potentiometer system for Mode Selection Damper
REMOVAL AND INSTALLATION
Code No. P0546: No. 1 exhaust gas temperature sensor Circuit High Input
SENSOR
PTC HEATER RELAY CONTROL
Code No. P2127: Accelerator Pedal Position Sensor (sub) Circuit Low Input
COMMON RAIL CHECK
CONDENSOR FAN RELAY CONTROL
Code No. P0643: Analog Sensor Reference Voltage No. 1 Too High
Inspection Procedure 2: The Engine Warning Lamp Does Not Illuminate Right after the Ignition Switch Is Turned the "ON" Position
Code No. P0652: Analog Sensor Reference Voltage No. 2 Too Low
Code No. P2150: Injector Common 2 (Cylinder No. 2 and No. 3) Circuit Earth Short
Code No. P0299: Turbocharger Under Boost Condition
DISASSEMBLY AND REASSEMBLY
Code No. P064C: Glow Control Unit Malfunction
Code No. P0683: Glow Control Unit Communication Abnormality
Inspection Procedure 5: Starting Impossible (Starter operative but no initial combustion)
FUEL GAUGE UNIT CHECK
Code No. P2151: Injector Common 2 (Cylinder No. 2 and No. 3) Circuit Battery Short
FUEL TANK
FUEL DRAINING
Code No. P2228: Barometric Pressure Sensor Circuit Low Input
EVACUATION OF AIR FROM FUEL LINE
Code No. P0405: EGR Valve Position Sensor Circuit Low Input
Code No. P0203: No. 3 Injector Circuit Malfunction
Inspection Procedure 14: Battery rundown
THROTTLE VALVE CONTROL SERVO CHECK
Code No. P0016: Crank Angle Sensor/Camshaft Position Sensor Phase Problem
Code No. P0628: Suction Control Valve Open
Code No. P1203: Capacitor Insufficient Charging
Code No. P1299: Variable Geometry Turbocharger Control System Malfunction (low pressure)
Code No. P0638: Throttle Valve Control Servo Stuck
FUEL LEAK CHECK OF FUEL TANK
Code No. P0607: Engine-ECU (sub CPU) Malfunction
Code No. P0113: Intake Air Temperature Sensor No. 1 Circuit High Input
Code No. P0401: EGR Flow Insufficient
SPECIAL TOOLS
SEALANTS
Code No. P2138: Accelerator Pedal Position Sensor (Main and Sub) Range/Performance Problem
Actuator Test Reference Table
Code No. P0490: EGR Valve Position Sensor Circuit High Input
Code No. P0204: No. 4 Injector Circuit Malfunction
Code No. P2128: Accelerator Pedal Position Sensor (sub) Circuit High Input
Code No. P0108: Manifold Absolute Pressure Sensor Circuit High Input
Code No. P0102: Air flow Sensor Circuit Low Input
Code No. P0545: No.1 Exhaust Gas Temperature Sensor Circuit Low Input
Code No. P062F: EEPROM Malfunction
Code No. P0340: Camshaft Position Sensor System
Code No. P1272: Pressure Limiter Malfunction
Code No. P0629: Suction Control Valve Battery Short
Code No. P0191: Rail Pressure Sensor Range/Performance Problem
Code No. P2229: Barometric Pressure Sensor Circuit High Input
Inspection Procedure 28: Rear Window Defogger System
REMOVAL AND INSTALLATION
Inspection Procedure 18: 1st and 2nd Rail Switch System
SERVICE SPECIFICATIONS
Code No. P0402: EGR Flow Excessive
REMOVAL AND INSTALLATION
FUEL PRESSURE CONTROL
Code No. P0502: Vehicle Speed Sensor Low Input <2WD-M/T and 4WD vehicles>
DIAGNOSIS SYSTEM
IDLE SPEED CONTROL (ISC)
COMMON RAIL
Code No. P0107: Manifold Absolute Pressure Sensor Circuit Low Input
Inspection Procedure 4: Starting Impossible (No Initial Combustion)
Code No. P0203: No. 3 Injector Circuit Malfunction
Code No. P2148: Injector Common Circuit Battery Short
Code No. P1274: Supply Pump Protection
SPECIAL TOOLS
Inspection Procedure 23: A/C Compressor Relay System
GENERAL INFORMATION
Code No. P0072: Intake Air Temperature Sensor No. 2 Circuit Low Input
Code No. P0620: Alternator Control Circuit
Code No. P2123: Accelerator Pedal Position Sensor (main) Circuit High Input
Code No. P2146: Injector Common 1 (cylinder No. 1 and No. 4) Circuit Open
Code No. P0113: EGR Gas Temperature Sensor Circuit High Input
Code No. P252F: Engine Oil Level Malfunction
Code No. P0183: Fuel Temperature Sensor Circuit High Input
FUEL TEMPERATURE SENSOR CHECK
Code No. P0204: No. 4 Injector Circuit Malfunction
Code No. P0089: Suction Control Valve Stuck
Inspection Procedure 6: Improper Starting (Long time to start)
Code No. P0551: Power Steering Fluid Pressure Switch System
EVACUATION OF WATER FROM FUEL FILTER
Inspection Procedure 21: Condenser Fan Relay System
Code No. P0489: EGR Valve Position Sensor Circuit Low Input
Code No. P0605: Read Only Memory (FLASH ROM) Malfunction
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Code No. P0123: Throttle Position Sensor Circuit High Input
Code No. P0192: Rail Pressure Sensor Circuit Low Input
ENGINE CONTROL RELAY CONTINUITY CHECK
REMOVAL AND INSTALLATION
Code No. U1110: A/C-ECU Time-out
Code No. P2146: Injector Common 1 (cylinder No. 1 and No. 4) Circuit Open
Inspection Procedure 26: PTC Heater Relay System
Code No. P1275: Supply Pump Exchange
Inspection Procedure 8: The Engine Stalls When Decelerating
Inspection Procedure 3: The Engine Warning Lamp Remains Illuminating and Never Goes Out or Is Blinking.
Code No. P0642: Analog Sensor Reference Voltage No. 1 Too Low
Code No. P0234: Turbocharger Overboost Condition
Code No. P2124: Accelerator Pedal Position Sensor (Main) Circuit High Input Intermittent
Code No. P0003: Suction Control Valve Open
Code No. P0118: Engine Coolant Temperature Sensor Circuit High Input
Code No. P0427: No. 2 Exhaust Gas Temperature Sensor (catalyst temperature) Circuit Low Input
Inspection Procedure 22: A/C Switch System
Code No.U1190: The Network System Diagnosis Code Output Permitted Signal Can Not Be Received
THROTTLE VALVE OPENING CONTROL
CHECK AT THE ECU TERMINALS
Code No. U1101: A/T-ECU Time-out
Inspection Procedure 10: A Large Amount of Fuel Consumption
Code No. P1273: Supply Pump Insufficient Flow
Code No. P2149: Injector Common 2 (cylinder No. 2 and No. 3) Circuit Open
Code No. P2149: Injector Common 2 (cylinder No. 2 and No. 3) Circuit Open
Code No. P0303: No. 3 Cylinder Injector Malfunction (No Injection)
REMOVAL AND INSTALLATION
Inspection Procedure 4: Starting Impossible (No Initial Combustion)
Inspection Procedure 11: Knocking, Abnormal Noise
Inspection Procedure 12: White Smoke
REMOVAL AND INSTALLATION
Code No. P1276: Fuel Filter Exchange
Code No. U1073: Bus Off
Code No. P1626: Injection Quantity Compensation Value Not Coding
Code No. P0630: Chassis Number not Programmed
Code No. P1497: DPF System Malfunction
CHECK CHART CLASSIFIED BY PROBLEM SYMPTOMS
Code No. P0341: Camshaft Position Sensor Range/Performance Problem
Inspection Procedure 14: Battery Rundown
FUEL FILTER REPLACEMENT
CONTROLLER AREA NETWORK (CAN)
CONTROL SYSTEM
A/C RELAY CONTROL
Code No. P0182: Fuel Temperature Sensor Circuit Low input
Code No. U1117 ETACS-ECU (Immobilizer-ECU) Time-out
Code No. P2147: Injector Common Circuit Earth Short
Inspection Procedure 20: 4LLC Switch System
Code No. P0304: No. 4 Cylinder Injector Malfunction (No Injection)
Code No. P2118: Throttle Valve Control (DC Motor) Current Malfunction
Data List Reference Table
ACTUATOR
Inspection Procedure 27: Blower Switch System
Code No. P0073: Intake Air Temperature Sensor No. 1 Circuit High Input
Inspection Procedure 24: Power Steering Fluid Pressure Switch System
SUCTION CONTROL VALVE CHECK
Code No. P0202: No. 2 Injector Circuit Malfunction
Code No. P1298: Variable Geometry Turbocharger Control System Malfunction (high pressure)
Code No. P0073: Intake Air Temperature Sensor No. 2 Circuit High Input
Code No. P2148: Injector Common 1 (Cylinder No. 1 and No. 4) Circuit Battery Short
Code No. P0606: Engine-ECU (main CPU) Malfunction
Code No. P0117: Engine Coolant Temperature Sensor Circuit Low Input
POWER SUPPLY CONTROL
Code No. P0515: Battery Temperature Sensor System
Code No. P1427: No. 3 Exhaust Gas Temperature Sensor (DPF temperature) Circuit Low Input
Code No. P0072: Intake Air Temperature Sensor No. 1 Circuit Low Input
GENERAL INFORMATION
INJECTOR CHECK
REMOVAL AND INSTALLATION
INSPECTION
Code No. P0193: Rail Pressure Sensor Circuit High Input
Code No. P0604: Random Access Memory (RAM) Malfunction
Code No. P0201: No. 1 Injector Circuit Malfunction
Inspection Procedure 1: Communication with Engine-ECU Is Not Possible
Code No. P0381: Glow Plug Open/Short Malfunction
Inspection Procedure 9: Poor Acceleration
Code No. P0219: Engine Overspeed Condition
Code No. P1277: Fuel Filter Freeze
REMOVAL AND INSTALLATION
Code No. P1499: Abnormally high DPF temperature
Code No. P0088: Common Rail High Pressure Malfunction
Code No. P2122: Accelerator Pedal Position Sensor (main) Circuit Low Input
Inspection Procedure 7: Improper Idling
Code No. P0106: Manifold Absolute Pressure Sensor Range/Performance Problem
REMOVAL AND INSTALLATION
Code No. P2147: Injector Common 1 (Cylinder No. 1 and No. 4) Circuit Earth Short
INSPECTION PROCEDURE USING OSCILLOSCOPE
DIAGNOSIS TROUBLESHOOTING FLOW
Code No. P0112: Intake Air Temperature Sensor No. 1 Circuit Low Input
Inspection Procedure 19: Back-up Lamp Switch System
SUPPLY PUMP
COMPONENT LOCATION
Code No. P1204: Capacitor Excessive Charging
Code No. P1428: No. 3 Exhaust Gas Temperature Sensor (DPF temperature) Circuit High Input
Code No. P0406: EGR Valve Position Sensor Circuit High Input
DIAGNOSIS FUNCTION
FUEL INJECTION CONTROL
GENERAL INFORMATION
Code No. U1109: ETACS-ECU Time-out
Code No. P0603: EEPROM Malfunction
Inspection Procedure 15: Overheating
INTAKE AIR TEMPERATURE SENSOR No. 2 CHECK
Code No. P1625: Injection Quantity Compensation Value Error
Code No. P0420: Catalyst Malfunction
Inspection Procedure 13: Black Smoke
Code No. P1498: Excessive PM Accumulated in DPF
Code No. P2454: Exhaust Differential Pressure Sensor Circuit Low Input
Code No. P0301: No. 1 Cylinder Injector Malfunction (No Injection)
GENERAL INFORMATION
Code No. P0103: Air Flow Sensor Circuit High Input
Code No. P0403: EGR Valve (DC Motor) Malfunction
Code No. P0513: Immobilizer Malfunction
INSPECTION CHART FOR TROUBLE SYMPTOMS
Code No. P1608: Battery Current Sensor System
Code No. P0653: Analog Sensor Reference Voltage No. 2 Too High
INSPECTION CHART FOR DIAGNOSIS CODES
Inspection Procedure 16: Engine-ECU Power Supply System
Code No. P0202: No. 2 Injector Circuit Malfunction
Inspection Procedure 29: DPF Lamp System
Code No. P0048: Variable Geometry Control Solenoid Valve Circuit High Input
Code No. P0047: Variable Geometry Control Solenoid Valve Circuit Low Input
Code No. P0004: Suction Control Valve Battery Short
Code No. P0112: EGR Gas Temperature Sensor Circuit Low Input
FUEL LINE LEAK CHECK
Inspection Procedure 17: Engine-ECU Battery Back-up System
Code No. P2413: EGR System Performance
Code No. P0093: Fuel Leak Problem
Code No. U1102 ASTC-ECU Time-out
ENGINE COOLANT TEMPERATURE SENSOR CHECK
Code No. P0122: Throttle Position Sensor Circuit Low Input
Code No. P0335: Crank Angle Sensor System
Code No. P0428: No. 2 Exhaust Gas Temperature Sensor (catalyst temperature) Circuit High Input
Code No. P2455: Exhaust Differential Pressure Sensor Circuit High Input
INTAKE AIR TEMPERATURE SENSOR No. 1 CHECK
Code No. P0336: Crank Angle Sensor Range/Performance Problem
Code No. P0302: No. 2 Cylinder Injector Malfunction (No Injection)
Inspection Procedure 25: Glow System