DISASSEMBLY AND REASSEMBLY







Disassembly steps


1.
Roll stopper bracket front


2.
Vehicle speed sensor


3.
Back-up lamp switch assembly


4.
Lock ball assembly


5.
Wiring harness clamp bracket


6.
Wiring harness clamp bracket


7.
Wiring harness clamp bracket


8.
Control cable bracket


9.
Transmission case hanger No.1

>>N<<
10.
Select lever shoe
<<A>>

11.
Bellcrank


12.
Lever lock pin


13.
Control shift lever


14.
Dust boot


15.
Clamp

>>M<<
16.
Air breather


17.
Control shaft cover sub-assembly

>>L<<
18.
Control shift lever gasket


19.
Shift and select lever shaft assembly

>>K<<
20.
Oil seal


21.
Clutch fluid line bracket




Disassembly steps

>>J<<
22.
Transmission case cover sub-assembly


23.
Gear shift fork No.3

>>I<<
24.
Synchronizer hub sleeve No.3

>>H<<
25.
Shaft snap ring
<<B>>
>>G<<
26.
Synchronizer clutch hub No.3

>>G<<
27.
Synchromesh shifting key spring No.3 (A)

>>G<<
28.
Synchromesh shifting key spring No.3 (B)

>>G<<
29.
Synchronizer ring set No.5
<<C>>
>>F<<
30.
Flange nut


31.
5th gear


32.
Needle roller bearing
<<D>>
>>E<<
33.
5th drive gear


34.
Shaft snap ring


35.
Shaft snap ring


36.
Shaft snap ring


37.
Reverse idler gear shaft mounting bolt


38.
Gasket


39.
Rear bearing retainer mounting bolt


40.
Rear bearing retainer

>>D<<
41.
Transmission case sub-assembly




Disassembly steps

>>C<<
42.
Reverse shift arm bracket assembly


43.
Gear shift fork shaft No.2


44.
Gear shift head No.1


45.
Shaft snap ring

>>B<<
46.
Gear shift fork shaft No.1

>>B<<
47.
Gear shift fork assembly No.1


48.
Roller


49.
Shaft snap ring


50.
Gear shift fork shaft No.3


51.
Shaft snap ring


52.
Reverse shift fork


53.
Gear shift fork assembly No.2

>>A<<
54.
Reverse idler gear shaft

>>A<<
55.
Reverse idler thrust washer

>>A<<
56.
Reverse idler gear sub-assembly


57.
Input shaft assembly


58.
Output shaft assembly


59.
Differential assembly


60.
Clutch housing case assembly

DISASSEMBLY SERVICE POINTS



<<A>> BELLCRANK REMOVAL



Remove the fixing nuts shown, then separate the control shift lever from the bellcrank

<<B>> SYNCHRONIZER CLUTCH HUB No.3 REMOVAL



Using special tool, Puller set (MB992221), remove the synchronizer clutch hub No.3.

<<C>> FLANGE NUT REMOVAL



1.Using special tool, Input shaft holder (MD998802), lock the input shaft.

2.Remove the flange nut from output shaft assembly.

<<D>> 5TH DRIVE GEAR REMOVAL



Using special tool, Rear axle bearing outer race puller (MB990801), remove the 5th drive gear.

ADJUSTMENT BEFORE ASSEMBLY



DIFFERENTIAL SIDE BEARING PRELOAD ADJUSTMENT


1.Set the differential assembly to the clutch housing case assembly.

2.Push and fit the tapered roller bearing outer race by hand.
3.To fit the tapered roller bearing outer race, rotate the differential assembly by hand about 10 times.

4.Put the clutch housing case assembly on the surface table and use a height gauge to measure the dimension "A" which is from the mating surface of the clutch housing case assembly to the end surface of the tapered roller bearing outer race.

5.Put the straight edge on the mating surface of the transmission case assembly and measure the dimension "B" with a vernier caliper.
6.Select the shim whose dimension is the difference between "B" and "A."
7.Install the differential assembly to the clutch housing case assembly. Tighten the transmission case bolts to the specified torque of 29 ± 5.8 N·m.

8.Using special tool, Preload socket (MB992038), measure the rotational starting torque of differential case. When it is not within the standard range, reselect the shim.
Standard value: 0.8 - 1.6 N·m

OUTPUT SHAFT ASSEMBLY BEARING PRELOAD ADJUSTMENT


1.Set the output shaft assembly to the clutch housing case assembly.

2.Push and fit the tapered roller bearing outer race by hand.
3.To fit the tapered roller bearing outer race, rotate the output shaft assembly by hand.

4.Put the clutch housing case assembly on the surface table and measure the dimension "A" which is from the mating surface of the clutch housing case assembly to the end surface of the bearing outer race, with a height gauge.

5.Put the straight edge on the mating surface of the transmission case assembly and measure the dimension "B" with a vernier caliper.
6.Select the shim whose dimension is the difference between "B" and "A."
7.Install the output shaft assembly and differential assembly to the clutch housing case assembly. Tighten the transmission case bolts to the specified torque of 29 ± 5.8 N·m.
8.Place the selected shim, then install the output shaft assembly.
9.Install the rear bearing retainer mounting bolt to specified torque of 42 ± 8.4 N·m.

10.Install the 5th gear mounting lock nut to measure rotational starting torque.

11.Measure the rotational starting torque of output shaft. When it is not within the standard range, reselect the shim.
Standard value: 0.8 - 1.6 N·m

REASSEMBLY SERVICE POINTS



>>A<< REVERSE IDLER GEAR SUB-ASSEMBLY / REVERSE IDLER THRUST WASHER / REVERSE IDLER GEAR SHAFT INSTALLATION



1.Install the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft.
2.Before installing the transmission case assembly, confirm that the reverse idler gear addition mark is positioned as show in the illustration.

>>B<< GEAR SHIFT FORK ASSEMBLY No.1 / GEAR SHIFT FORK SHAFT No.1 INSTALLATION


1.Fit the shaft snap ring onto the gear shaft fork shaft No.1.

2.Bring up the notch in the gear shift fork shaft No.3 to the reverse shift fork into neutral position, and move the roller in the reverse shift fork to the gear shift fork shaft No.3 side.

3.Pass the gear shift fork shaft No.1 through the gear shift fork assembly No.1 and reverse shift fork in that order, then install it to the clutch housing case assembly.

>>C<< REVERSE SHIFT ARM BRACKET ASSEMBLY INSTALLATION



Fit the arm tip of the reverse shift fork into the mating slot in the reverse shift arm bracket assembly.

>>D<< TRANSMISSION CASE SUB-ASSEMBLY INSTALLATION



Apply a 1.2 mm diameter bead of sealant as illustrated onto the transmission case sub-assembly.
Specified sealant: Mitsubishi Part No. MD974421 or equivalent

>>E<< 5TH DRIVE GEAR INSTALLATION



1.Install special tool Output shaft adapter (MB992219) until it hits the end face of the output shaft.

2.Install the 5th drive gear.

3.Set special tool Installer (MB992216) on top of the 5th drive gear.

4.Install the center bolt that is included in the set of special tool Installer (MB992216) as shown.

5.Press-fit the 5th drive gear as shown.

>>F<< FLANGE NUT INSTALLATION



1.Using special tool Input shaft holder (MD998802), lock the input shaft.

2.Install the flange nut from output shaft assembly.
3.Tighten the flange nut to the specified torque of 123 ± 36.9 N·m.
4.Stake the flange nut.

>>G<< SYNCHRONIZER RING SET No.5 / SYNCHROMESH SHIFTING KEY SPRING No.3 (A) / SYNCHROMESH SHIFTING KEY SPRING No.3 (B) / SYNCHRONIZER CLUTCH HUB No.3 INSTALLATION



1.Install the synchromesh shifting key springs No.3 onto the synchronizer ring assembly holding the claws and rotation stops of the key springs in the illustrated positions.

2.Make sure that the rotation stops of the synchromesh shifting key springs No.3 fit into the mating holes in the synchronizer ring set No.5.

3.Compress the key springs into place inside the hub as shown.

4.Install special tool Input shaft adapter (MB992220) until it hits the end face of the input shaft.

5.Set special tool Installer (MB992216) on top of the synchronizer clutch hub No.3.

6.Install the center bolt that is a part of the set of special tool Installer (MB992216) as shown.

7.Press-fit the synchronizer clutch hub No.3 as shown.

>>H<< SHAFT SNAP RING INSTALLATION



Select a shaft snap ring that allows distance of the thrust crevice of synchronizer clutch hub No.3 to fall within the standard value range.
Standard value: 0 - 0.1 mm
note Try on snap rings in the decreasing order of thickness, and install the first one that fits into the hub.

>>I<< SYNCHRONIZER HUB SLEEVE No.3 INSTALLATION



Put the synchronizer hub sleeve No.3 and gear shaft fork assembly No.3 together, then install the synchronizer hub sleeve No.3 in the illustrated direction.

>>J<< TRANSMISSION CASE COVER SUB-ASSEMBLY INSTALLATION



Apply a 1.2 mm diameter bead of sealant as illustrated onto the transmission case cover sub-assembly.
Specified sealant: Mitsubishi Part No. MD974421 or equivalent

>>K<< OIL SEAL INSTALLATION



1.Using special tools to install the oil seal.

  • Oil seal installer (MB992212)

  • Handle (MB992075)
2.Apply grease to the oil seal lip area.
Specified grease: Mitsubishi Part No. 0101011 or equivalent

>>L<< CONTROL SHIFT LEVER GASKET INSTALLATION



Install the control shift lever gasket to the control shaft cover with the projection of the gasket in the illustrated position.

>>M<< AIR BREATHER INSTALLATION



Using special tool Crankshaft adapter (MB992000), install the air breather.

>>N<< SELECT LEVER SHOE INSTALLATION




1.Apply grease to the select lever shoe hole and bellcrank pin.
Specified grease: Mitsubishi Part No. 0101011 or equivalent
2.Install the select lever shoe to the bellcrank.