FRONT BODY


HEADLAMP SUPPORT



  • The crush box structure, which has an octagonal cross-section at the front end of the front sidemember, has been adopted. This structure can effectively absorb energy upon frontal impact and reduces the vehicle repair cost caused by a light collision.
  • The bolt-on headlamp support panel upper is used to improve maintainability.
1.
 Front bumper reinforcement
2.
 Headlamp support panel upper
3.
 Front end crossmember gusset
4.
 Front end crossmember upper
5.
 Nut plate <Vehicles with intercooler>
6.
 Radiator bracket lower A
7.
 Front end crossmember bulkhead
8.
 Radiator bracket lower B
9.
 Shipping hook front
10.
 Shipping reinforcement front
11.
 Front end crossmember lower



FENDER SHIELD



  • The front frame structure is supported in three directions by the dash crossmember centre, dash crossmember lower and front sidemember rear in order to improve the frontal collision characteristics, and increase the vehicle body rigidity.
  • The padding structure of the fender has been adopted to efficiently absorb energy upon impact and improve the pedestrian protection capability.
1.
 Upper side bar front
2.
 Front end upper bar side
3.
 Front fender bracket
4.
 Upper frame bulkhead front
5.
 Fender shield frame upper outer
6.
 Upper frame bulkhead centre
7.
 Upper frame bulkhead rear
8.
 Front fender bracket
9.
 Front upper frame inner
10.
 Harness bracket
11.
 Spring house corner gusset
12.
 Spring house bracket reinforcement
13.
 Spring house bracket front
14.
 Spring house panel rear
15.
 Horn bracket
16.
 Spring house harness bracket
17.
 Suction hose bracket
18.
 Spring house panel
19.
 Power steering reservoir tank bracket
20.
 Engine mounting bracket upper
21.
 Front fender shield
22.
 Engine mounting gusset
23.
 Condense tank reinforcement
24.
 Fender gusset
25.
 Front fender bracket
26.
 Front sidemember
27.
 Clutch tube bracket <M/T>
28.
 Engine-ECU bracket
29.
 Relay box bracket
30.
 Transmission mounting gusset

FRONT SIDEMEMBER REINFORCEMENT
1.
 Front sidemember extension
2.
 Front sidemember outer
3.
 Front brake hose bracket
4.
 Front sidemember reinforcement rear lower
5.
 Front sidemember rear bulkhead
6.
 Front sidemember rear
7.
 Height sensor bracket
8.
 Dash crossmember extension lower
9.
 Front body frame to side sill brace
10.
 Front suspension crossmember bracket front
11.
 Front sidemember inner
12.
 Front sidemember plate
13.
 Front sidemember bulkhead front
14.
 Engine mounting bulkhead
15.
 Front suspension crossmember bulkhead
16.
 Headlamp bracket lower
17.
 Headlamp support panel
18.
 Engine mounting reinforcement
19.
 Engine mounting bracket <Except RALLIART>
20.
 Engine mounting bracket front <RALLIART>
21.
 Engine mounting bracket rear <RALLIART>
22.
 Front sidemember brace upper
23.
 Front sidemember reinforcement rear <LH drive vehicles>






1.
 Dash crossmember extension lower
2.
 Front body frame to side sill brace
3.
 Front sidemember rear
4.
 Front sidemember rear bulkhead
5.
 Front sidemember reinforcement rear lower
6.
 Front sidemember outer
7.
 Front brake hose bracket
8.
 Front sidemember extension
9.
 Front sidemember plate
10.
 Battery tray stay front
11.
 Battery tray stay rear
12.
 Front suspension crossmember bracket front
13.
 Front sidemember inner
14.
 Front sidemember reinforcement rear <RH drive vehicles>
15.
 Front sidemember brace upper
16.
 Transmission mounting bracket
17.
 Connecter bracket
18.
 Headlamp support panel
19.
 Headlamp bracket lower
20.
 Front suspension crossmember bulkhead
21.
 Transmission mounting bulkhead




FRONT DECK



  • The impact absorbing opening on the cowl top outer reinforcement upper has been added to efficiently absorb energy upon impact and improve the pedestrian protection capability.
  • Rigidity was heightened and driving stability was improved by bonding the fender shield frame upper outer and front pillar by the upper frame to front pillar brace.
1.
 Cowl top panel lower
2.
 Wiper B bracket
3.
 Cowl top stay bracket rear
4.
 Cowl top outer reinforcement upper
5.
 Cowl top panel inner
6.
 Cowl top panel outer
7.
 Deck crossmember stay bracket
8.
 Brake pedal support bracket
9.
 Clutch pedal support bracket <M/T>
10.
 Upper frame extension inner
11.
 Brake pedal support reinforcement
12.
 Front fender bracket
13.
 Cowl top outer reinforcement lower
14.
 Upper frame to front pillar brace

DASH PANEL



  • The front frame structure is supported in three directions by the dash crossmember centre, dash crossmember lower and front sidemember rear in order to improve the frontal collision characteristics, and increase the vehicle body rigidity.
  • The 590-MPa class high tensile strength steel panels have been adopted for the dash crossmember centre, dash crossmember extension, dash panel reinforcement and dash crossmember side to improve the body rigidity.
1.
 Brake tube bracket
2.
 Harness bracket
3.
 Dash crossmember centre
4.
 Dash crossmember extension
5.
 Canister bracket
6.
 Dash heat protector bracket
7.
 Dash panel
8.
 Electric power steering bracket <Vehicles with electric power steering>
9.
 Backbone reinforcement front
10.
 Dash panel lower
11.
 Accelerator pedal bracket
12.
 Steering shaft bracket
13.
 Dash panel reinforcement
14.
 Clutch pedal reinforcement lower <M/T>
15.
 Dash crossmember side
16.
 Dash crossmember lower bulkhead
17.
 Dash crossmember lower
18.
 Accelerator pedal bracket lower
19.
 Clutch pedal reinforcement <M/T>