Code No. U1180: Combination Meter Time-out


caution If diagnosis code U1180 is set from AS&G-ECU, surely perform CAN bus line diagnosis.
caution Replace ECU after certainly confirming that the communication circuits are normal.

TROUBLE JUDGMENT


Check Conditions
  • 2 seconds later after the ignition switch has been in "ON" position or the engine has started up.
  • The battery voltage is more than 10 V and is less than 16 V.
  • The diagnosis code U0141 is not detected.
Judgement Criterion
  • Unable to receive the signals from the combination meter for 4 seconds.

COMMENTS ON TROUBLE SYMPTOM


Current malfunction
  • The failure is possibly caused by malfunction of the harness and connector in CAN bus line between AS&G-ECU and combination meter, by malfunction in the power supply system of combination meter, in combination meter itself, in AS&G-ECU.
Past malfunction
  • Proceed with troubleshooting focusing on malfunction of the harness and connector in CAN bus line between AS&G-ECU and combination meter and malfunction in the power supply system of combination meter. For diagnosis procedure, refer to how to cope with past malfunctions (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Treat Past Trouble ).
    note In the case of past malfunctions, M.U.T.-III CAN bus line diagnosis cannot detect a malfunction even if there is a malfunction in CAN bus. Therefore, check CAN bus line as in the case of response to intermittent malfunctions (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ). It is possible to narrow down areas with a high possibility of malfunctions from diagnosis codes set to each ECU that performs CAN communication (Refer to GROUP 54C - Explanation about the M.U.T.-III CAN Bus Diagnostics ).
FAIL-SAFE AND BACKUP FUNCTION
  • In the normal operation, the auto stop is prohibited. If the malfunction is detected during the auto stop, the auto start is prohibited.

PROBABLE CAUSES



  • Failed harness and connector
  • Failed combination meter
  • Failed AS&G-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnosis

  • Use M.U.T.-III to perform CAN bus line diagnosis.

Q. Is the check result normal?
Go to Step 2.
Repair CAN bus line (Refer to GROUP 54C - Troubleshooting - CAN Bus Diagnostics Table ). After repairing CAN bus line, go to Step 4.

STEP 2. M.U.T.-III diagnosis code

  • Confirm the diagnosis code is set from the combination meter.

Q. Is the diagnosis code set?
Perform troubleshooting of the combination meter (Refer to GROUP 54A - Combination Meter - Diagnosis Code Chart ).
Go to Step 3.

STEP 3. M.U.T.-III diagnosis code

  • Reconfirmation of diagnosis code.
Confirm again the diagnosis code is set from the AS&G-ECU.

  1. Erase the set diagnosis code.
  2. Ignition switch: "LOCK" (OFF) → ON
  3. Confirm whether the diagnosis code is set.

Q. Is the diagnosis code set?
After replacing the AS&G-ECU, go to Step 4.
Intermittent malfunction in CAN bus line between AS&G-ECU and combination meter (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).

STEP 4. M.U.T.-III diagnosis code

  • Reconfirmation of diagnosis code.
Confirm again the diagnosis code is set from the AS&G-ECU.

  1. Erase the set diagnosis code.
  2. Ignition switch: "LOCK" (OFF) → ON
  3. Confirm whether the diagnosis code is set.

Q. Is the diagnosis code set?
Go to Step 1.
Check end.