Code No. B1626 Front passenger’s lap pre-tensioner (squib) system (open circuit of squib circuit)


caution If the diagnosis code B1626 is set to SRS-ECU, be sure to diagnose the CAN bus line.

OPERATION
Only when the frontal impact exceeding the threshold is simultaneously detected (turned ON) by the front impact sensor as well as by the analogue G-sensor and safing G-sensor in SRS-ECU, the electric current is supplied from SRS-ECU to the lap pre-tensioner (squib).

TROUBLE JUDGEMENT
The code is set when the open circuit occurs to the SRS-ECU passenger’s lap pre-tensioner (squib) circuit.

PROBABLE CAUSES

  • Poor contact of connector
  • Open circuit to lap pre-tensioner (squib) circuit
  • Malfunction of SRS-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics.
Use M.U.T.-III to diagnose the CAN bus lines.

Q. Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).

STEP 2. Check whether the diagnosis code is reset.
(1)Connect the negative battery terminal.
(2)After erasing the diagnosis code memory, check the diagnosis code again.
(3)Disconnect the negative battery terminal.

Q. Is the diagnosis code No. B1626 set?
Go to Step 3.
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).

STEP 3. Diagnosis check by dummy resistor connection.
(1)Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.

(2)Use the flat-tipped screwdriver to pull out the locking button of harness side connector. After releasing the lock, disconnect the lap pre-tensioner harness side connector.

(3)Connect the special tool dummy resistor (MB991865) to the special tool resistor harness (MB991884).
(4)Connect the special tool resistor harness to the lap pre-tensioner harness side connector.
(5)Connect the negative battery terminal.
(6)After erasing the diagnosis code memory, check the diagnosis code again.
(7)Disconnect the negative battery terminal.

Q. Is the diagnosis code No. B1626 set?

Go to Step 4.

Replace the seat belt with pre-tensioner (Refer to ).

STEP 4. Resistance measurement at the SRS-ECU connector and the lap pre-tensioner connector.
(1)Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.

(2)While pushing the part "A" indicated in the figure of the harness side connector, turn the lock lever to the direction of the arrow to release the lock lever, and disconnect the SRS-ECU connector.

(3)
danger To release the SRS-ECU connector short spring in the following operations, disconnect this lap pre-tensioner connector, and keep the squib circuit shorted.
Use the flat-tipped screwdriver to pull out the locking button of harness side connector. After releasing the lock, disconnect the lap pre-tensioner harness side connector.

(4)
caution The short spring may not be released due to the insufficient insertion. Therefore, insert the insulator for 4 mm or more.
Insert an insulator (width: 3 mm, thickness: 0.5 mm) such as cable tie between the PA2-, PA2+, and then release the short spring.

(5)Connect special tool resistor harness (MB991884) to the removed lap pre-tensioner harness side connector.

(6)Take the measurements below at the resistor harness and SRS-ECU harness side connector.

  • Continuity PA2- line between SRS-ECU connector and lap pre-tensioner harness connector
  • Continuity PA2+ line between SRS-ECU connector and lap pre-tensioner harness connector
OK: Continuity (less than 2 Ω)

Q. Is the check result normal?

Go to Step 5.

Repair the wiring harness PA2-, PA2+ line between the SRS-ECU connector and the lap pre-tensioner connector.

STEP 5. Check whether the diagnosis code is reset.

Q. Is the diagnosis code No. B1626 set?
Replace SRS-ECU (Refer to ).
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).