Code No. U0167: KOS-ECU <Vehicles With KOS> or WCM <Vehicles With WCM> Communication Error


caution If diagnosis code U0167 is stored in the engine-ECU, surely perform CAN bus line diagnosis.
caution Replace ECU after certainly confirming that the communication circuits are normal.

TROUBLE JUDGEMENT


Check Condition
  • After the engine is cranked.
  • Ignition switch is "ON" position.
Judgement Criterion
  • Unable to receive KOS-ECU <Vehicles with KOS> or WCM (immobilizer-ECU) <Vehicles with WCM> signals through the CAN bus line.

COMMENTS ON TROUBLE SYMPTOM


Current malfunction
  • The failure is possibly caused by malfunction of the harness and connector in CAN bus line between engine-ECU and KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM>, by malfunction in the power supply system of KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM>, in KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM> itself, in engine-ECU.
Past malfunction
  • Proceed with troubleshooting focusing on malfunction of the harness and connector in CAN bus line between engine-ECU and KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM> and malfunction in the power supply system of KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM>. For diagnosis procedure, refer to how to cope with past malfunctions. (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Treat Past Trouble ).
    note In the case of past malfunctions, M.U.T.-III CAN bus line diagnosis cannot detect a malfunction even if there is a malfunction in CAN bus. Therefore, check CAN bus line as in the case of response to intermittent malfunctions (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ). It is possible to narrow down areas with a high possibility of malfunctions from diagnosis codes set to each ECU that performs CAN communication (Refer to GROUP 54C - Explanation about the M.U.T.-III CAN Bus Diagnostics ).

FAIL-SAFE AND BACKUP FUNCTION



  • Engine start is prohibited.

PROBABLE CAUSES



  • Failed harness and connector
  • Failed KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM>
  • Failed engine-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnosis

  • Use M.U.T.-III to perform CAN bus line diagnosis.

Q. Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting - CAN Bus Diagnostics Table ). After repairing the CAN bus line, go to Step 4.

STEP 2. M.U.T.-III diagnosis code

  • Confirm the diagnosis code is set from the KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM>.

Q. Is diagnosis code set?
Perform troubleshooting of KOS-system <Vehicles with KOS> or WCM-system <Vehicles with WCM> (Refer to GROUP 42B - Troubleshooting - Diagnosis Code Chart <Vehicles with KOS>, Refer to GROUP 42C - Troubleshooting - Diagnosis Code Chart <Vehicles with WCM>).
Go to Step 3.

STEP 3. M.U.T.-III diagnosis code

  • Reconfirmation of diagnosis code.
Confirm again the diagnosis code is set from the engine-ECU.

  1. Erase the set diagnosis code.
  2. Ignition switch: LOCK (OFF) → ON
  3. Confirm whether the diagnosis code is set.

Q. Is diagnosis code set?
After replacing engine-ECU, go to Step 4.
Intermittent malfunction in CAN bus line between engine-ECU and KOS-ECU <Vehicles with KOS> or WCM <Vehicles with WCM> (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).

STEP 4. M.U.T.-III diagnosis code

  • Reconfirmation of diagnosis code.
Confirm again the diagnosis code is set from the engine-ECU.

  1. Erase the set diagnosis code.
  2. Ignition switch: LOCK (OFF) → ON
  3. Confirm whether the diagnosis code is set.

Q. Is diagnosis code set?
Go to Step 1.
Check end.