Code No. U0141: ETACS-ECU CAN time-out


caution If diagnosis code No.U0141 is set in the heater control panel or A/C control panel, diagnose the CAN main bus line.
caution Whenever the ECU is replaced, ensure that the communication circuit is normal.

TROUBLE JUDGMENT
The heater control panel or A/C control panel receives air conditioner operation-related signal from the ETACS-ECU via the CAN bus lines. If the heater control panel or A/C control panel can not receive the air conditioner operation-related signal at all on the ETACS-ECU, diagnosis code No.U0141 will be set.

COMMENTS ON TROUBLE SYMPTOM
Current trouble
  • Connector(s) or wiring harness in the CAN bus lines between the ETACS-ECU and the heater control panel or A/C control panel, the power supply system to the ETACS-ECU, the ETACS-ECU itself, or the heater control panel or A/C control panel may be faulty.
Past trouble
  • Carry out diagnosis with particular emphasis on connector(s) or wiring harness in the CAN bus lines between the ETACS-ECU and the heater control panel or A/C control panel, and the power supply system to the ETACS-ECU. For diagnosis procedures, refer to "How to treat past trouble" (Refer to GROUP 00 - How to Treat Past Trouble ).
    note For a past trouble, you can not find it by the M.U.T.-III CAN bus diagnostics even if there is any failure in CAN bus lines. In this case, refer to GROUP 00, How to Cope with Intermittent Malfunction and check the CAN bus lines. You can narrow down the possible cause of the trouble by referring to the diagnosis code, which is set regarding the CAN communication-linked ECUs (Refer to GROUP 54C - CAN Bus Line Diagnostic Flow ).
    caution If the ignition switch is turned on without starting the engine and then three minutes pass, the heater control panel or A/C control panel may store U0141 as past trouble.

PROBABLE CAUSES

  • Damaged harness wires and connectors
  • Malfunction of ETACS-ECU
  • Malfunction of the heater control panel or A/C control panel

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.

Q. Is the check result normal?
Go to Step 2
Repair the CAN bus lines (Refer to GROUP 54C, Troubleshooting ). On completion, go to Step 6.

STEP 2. M.U.T.-III other system diagnosis code
Check whether the ETACS-related diagnosis code is set.

Q. Is the diagnosis code set?
Diagnose the ETACS-ECU. Refer to .
Go to Step 3

STEP 3. M.U.T.-III other system diagnosis code
Check if a diagnosis code, which relates to CAN communication-linked systems below, is set.

  • combination meter
    U0141: ETACS-related time-out diagnosis code

Q. Is the diagnosis code set?
Go to Step 4
Go to Step 5

STEP 4. Check whether the diagnosis code is reset.
Recheck if the diagnosis code is set.
(1)Erase the diagnosis code.
(2)Ignition switch: LOCK (OFF) to ON
(3)Check if the diagnosis code is set.

Q. Is the diagnosis code set?
Replace the ETACS-ECU, and then go to Step 6.
A poor connection, open circuit or other intermittent malfunction in the CAN bus line between the ETACS-ECU and the heater control panel or A/C control panel (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).

STEP 5. Check whether the diagnosis code is reset.
Recheck if the diagnosis code is set.
(1)Erase the diagnosis code.
(2)Ignition switch: LOCK (OFF) to ON
(3)Check if the diagnosis code is set.

Q. Is the diagnosis code set?
Replace the heater control unit or A/C-ECU, and then go to Step 6.
A poor connection, open circuit or other intermittent malfunction in the CAN bus line between the ETACS-ECU and the heater control panel or A/C control panel (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).

STEP 6. Check whether the diagnosis code is reset.
Recheck if the diagnosis code is set.
(1)Erase the diagnosis code.
(2)Ignition switch: LOCK (OFF) to ON
(3)Check if the diagnosis code is set.

Q. Is the diagnosis code set?
Return to Step 1.
The procedure is complete.