REMOVAL AND INSTALLATION <2WD (EXCEPT HIGH RIDER)>



caution At the time of factory shipment or when the engine is overhauled, liquid gasket is used for the engine oil pan gasket. Use the replacement engine oil pan gasket since the sealed surface may interfere with surrounding parts, causing engine oil leak when the engine oil pan is installed on the vehicle using the liquid gasket.
Pre-removal Operation
  • Engine Room Under Cover Removal (Refer to GROUP 51 - Under Cover ).
  • Engine Oil Draining (Refer to GROUP 12 - On-vehicle Service, Engine Oil Replacement ).

Post-installation Operation
  • Engine Oil Refilling (Refer to GROUP 12 - On-vehicle Service, Engine Oil Replacement ).
  • Engine Room Under Cover Installation (Refer to GROUP 51 - Under Cover ).





Removal steps


1.
Engine oil level gauge and guide assembly


2.
O-ring


3.
Bell housing cover


4.
Engine oil pan drain plug

>>B<<
5.
Engine oil pan drain plug gasket
<<A>>

·
Steering column assembly and steering shaft joint assembly connection
<<B>>

·
Power steering gear & link assembly mounting bolt
<<B>>

·
Return tube clamp
<<B>>

·
Pressure tube clamp
<<C>>

6.
Engine oil pan and engine oil pan strainer assembly

>>A<<
7.
Engine oil pan

>>A<<
8.
Engine oil pan gasket

>>A<<
9.
Engine oil pan strainer

>>A<<
10.
Engine oil pan strainer gasket


11.
Stiffener

REMOVAL SERVICE POINTS



<<A>> STEERING COLUMN ASSEMBLY AND STEERING SHAFT JOINT ASSEMBLY DISCONNECTION



Disconnect the steering column assembly and the steering shaft joint assembly. (Refer to GROUP 37 - Steering Column Shaft Assembly ).

<<B>> POWER STEERING GEAR & LINK ASSEMBLY MOUNTING BOLT/RETURN TUBE CLAMP/PRESSURE TUBE CLAMP REMOVAL



Remove the mounting bolts of the power steering gear & link assembly and of the tube clamps, and hung the power steering gear & link assembly using a wire or other similar material. (Refer to GROUP 37 - Power Steering Gear Box and Linkage , and Power Steering Hoses ).

<<C>> ENGINE OIL PAN AND ENGINE OIL PAN STRAINER ASSEMBLY REMOVAL


1.Remove the engine oil pan mounting bolts.


2.
caution Do not use special tool oil pan FIPG cutter (MD998727) in area A of the engine oil pan. Using the special tool (MD998727) in area A may cause deformation of the cylinder block case assembly front lower because the cylinder block case assembly front lower is made of aluminium.
Tap special tool (MD998727) into the range B between the cylinder block assembly and the engine oil pan, and then slide the tool sideways.
note If any surrounding parts interfere with the removal, there is no need to use the special tool.
3.With the engine oil pan separated from the cylinder block assembly, remove the engine oil pan strainer mounting bolts, and then remove the engine oil pan together with the engine oil pan strainer.

INSTALLATION SERVICE POINTS



>>A<< ENGINE OIL PAN STRAINER GASKET/ENGINE OIL PAN STRAINER/ENGINE OIL PAN GASKET/ENGINE OIL PAN INSTALLATION


1.Remove sealant from the engine oil pan and cylinder block assembly surfaces.
2.Place the engine oil pan strainer into the engine oil pan. Then, insert the engine oil pan and engine oil pan gasket into the clearance between the cylinder block assembly and the power steering gear & link assembly.
3.Set the engine oil pan strainer gasket and the engine oil pan strainer in the engine oil pan to the cylinder block assembly, and tighten the engine oil pan strainer mounting bolts to the specified torque.
Tightening torque: 19 ± 3 N·m
4.Set the engine oil pan gasket and engine oil pan to the cylinder block assembly, and tighten the engine oil pan mounting bolts to the specified torque.
Tightening torque: 9.0 ± 3.0 N·m

>>B<< ENGINE OIL PAN DRAIN PLUG GASKET INSTALLATION



Replace the gasket with a new gasket. Install the new gasket in the direction shown in the illustration.