Code No. P0108: Manifold Absolute Pressure Sensor Circuit High Input




OPERATION



  • A power voltage of 5 V is applied to the manifold absolute pressure sensor power terminal (terminal No. 1) from the engine-ECU (terminal No. 72) and earthed to the engine-ECU (terminal No. 31) from the manifold absolute pressure sensor (terminal No. 3).
  • The sensor signal is inputted to the engine-ECU (terminal No. 37) from the manifold absolute pressure sensor output terminal (terminal No. 2).

FUNCTION



  • The manifold absolute pressure sensor converts the manifold absolute pressure into a voltage signal and inputs the signal to the engine-ECU.
  • In response to the signal, the engine-ECU corrects the fuel injection amount, etc.

TROUBLE JUDGMENT


Check Conditions
  • Battery positive voltage is 8 - 16 V
  • 2 seconds later after the ignition switch has been in "ON" position or the engine has started up
Judgment Criterion
  • The manifold absolute pressure sensor output voltage should exceed 4.72 V for 0.5 seconds.

PROBABLE CAUSES



  • Failed manifold absolute pressure sensor
  • Open circuit in manifold absolute pressure sensor circuit or loose connector contact

  • Failed engine-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III data list

  • Refer to Data List Reference Table .

  1. Item 6: Manifold absolute pressure sensor

Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.

STEP 2. Connector check: A-105 manifold absolute pressure sensor connector

Q. Is the check result normal?

Go to Step 3.

Repair or replace the connector.

STEP 3. Perform resistance measurement at A-105 manifold absolute pressure sensor connector.


  • Disconnect connector, and measure at harness side.
  • Resistance between terminal No. 3 and earth.
OK: Continuity (2 Ω or less)

Q. Is the check result normal?

Go to Step 7.

Go to Step 4.

STEP 4. Connector check: C-105 engine-ECU connector

Q. Is the check result normal?

Go to Step 5.

Repair or replace the connector.

STEP 5. Check harness between A-105 (terminal No. 3) manifold absolute pressure sensor connector and C-105 (terminal No. 31) engine-ECU connector.



  • Check earthing line for open circuit.

Q. Is the check result normal?

Go to Step 6.

Repair the damaged harness wire.

STEP 6. M.U.T.-III data list

  • Refer to Data List Reference Table .

  1. Item 6: Manifold absolute pressure sensor

Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU. When the engine-ECU is replaced, write the chassis number (Refer to GROUP 00 - Precautions Before Service - How to Perform Chassis Number Writing ). After replacing the engine-ECU, register the injector identification code and learn fuel injection (Refer to GROUP 00 - Precautions Before Service - What The Common Rail Engine Learns ). After registering the injector identification code, the vehicle equipped with the DPF carries out the forcible DPF regeneration. (Refer to GROUP 17 - Emission Control - Diesel Particulate Filter (DPF) System - Forcible DPF Regeneration ).

STEP 7. M.U.T.-III data list

  • Refer to Data List Reference Table .

  1. Item 6: Manifold absolute pressure sensor

Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the manifold absolute pressure sensor.