FUNCTION AND CONTROL BY ETACS-ECU.




Function
Function description
Headlamp
Headlamp automatic-shutdown function

Daytime running lamp function

Flasher timer function
Turn-signal lamp

Comfort flasher function

Hazard warning lamp

ESS (Emergency Stop signal System)

Fog lamp
Front fog lamp function

Rear fog lamp function

Interior lamp
Interior lamp dimmer control function

Interior lamp automatic-shutoff function

Ignition key cylinder illumination lamp control function


HEADLAMP



HEADLAMP AUTOMATIC-SHUTDOWN FUNCTION (THE INITIAL CONDITION: WITH FUNCTION)






  • If the ignition switch is turned OFF with the lighting switch ON, the lamp turns off automatically after 3 minutes. If the driver’s door is opened during the 3 minutes, the lamp turns off after 1 second.
  • If the lighting switch is turned to the tail lamp position or headlamp position from OFF with the ignition switch OFF, the lamps do not turn off automatically.
note This function can be cancelled through customisation (Refer to Customise Function ).

DAYTIME RUNNING LAMP FUNCTION






FLASHER TIMER FUNCTION



TURN-SIGNAL LAMP (THE INITIAL CONDITION: TURN SIGNAL LAMP CAN BE OPERATED WHEN THE IGNITION SWITCH IS IN THE ON POSITION)



When the turn-signal lamp switch is ON (LH or RH) with the ignition switch is ON, the turn-signal lamp output (flash signal) is turned ON.
If the lamp bulb of the front or rear turn-signal lamp has burned out, the flashing speed becomes faster to alert the driver that the lamp bulb has burned out.
note Using a customisation function, this function becomes available even when the ignition switch is in the ACC position. For more information about the customisation feature, refer to .

COMFORT FLASHER FUNCTION (THE INITIAL CONDITION: WITH FUNCTION)



With the ignition switch in the ON position, when the turn signal switch is turned ON momentarily (0.4 second or less), ETACS-ECU turns ON the turn signal lamp output, and flashes the turn signal lamp three times.
note Using the customisation function, "with function/without function" of the comfort flasher function and the switch acceptance time can be set. For more information about the customisation function (Refer to Customise Function ).

HAZARD WARNING LAMP



ETACS-ECU detects the signal that changes the hazard lamp switch from OFF to ON, and reverses the flashing state by the signal (to the flashing state when the hazard lamp is not flashing, and to the turned OFF state when flashing).
note
  1. The push-return switch has been adopted for the hazard lamp switch.
  2. Even if the lamp bulb has burned out, the flashing speed of the hazard lamp is not changed.

ESS (EMERGENCY STOP SIGNAL SYSTEM)*


When the ETACS-ECU receives the ESS activation request signal from the ABS-ECU or the ASC-ECU, it flashes the turn-signal lamps at high speed to inform the following car that the driver is applying the brake suddenly.
note *: For further details on the ESS, refer to GROUP 35B - General Information <vehicles without ASC> or GROUP 35C - General Information <vehicles with ASC>.

FOG LAMP



FRONT FOG LAMP FUNCTION








REAR FOG LAMP FUNCTION







INTERIOR LAMP



INTERIOR LAMP DIMMER CONTROL FUNCTION (THE INITIAL CONDITION: 15 SECONDS)






  1. When the ignition switch is OFF:
    By opening any door, the lamp turns ON (100%), and dims (50%) when the door is closed, then and turns off after 15 seconds.
    However, when the ignition switch is turned ON or the door lock is operated, the lamps turn off at that time.
  2. When the ignition switch is ON:
    By opening any door, the lamp (100%) turns ON and OFF when the door is closed.
  3. When all doors are closed, and the ignition key is removed*:
    With all the doors closed, when the ignition key is removed, the lamp turns ON (100%) after approximately 1 second (after the engine is stopped), and then gradually dims down to OFF after 15 seconds.
    By inserting the ignition key again or operating the door lock with the lamp lit, the lamps turns off.
note
  • *: For the vehicles with KOS, it is operated the same way when the steering lock is locked or when the emergency key is removed from the key cylinder.
  • The delayed lamp-off time and the operation times of the keyless entry interior lamp answer back can be changed by the customise function (Refer to ).

INTERIOR LAMP AUTOMATIC-SHUTOFF FUNCTION (THE INITIAL CONDITION: 30 MINUTES)






  • After 30 minutes with the interior lamp lit while the ignition switch is OFF, the lamp turns off automatically.
  • After 30 minutes with any door opened while the ignition switch is OFF, the lamp turns off automatically.
  • After the auto-turn OFF, the interior lamp returns to the illumination state when the doors are opened/closed, keyless entry transmitter switch is operated, or ignition switch is turned to ACC position. After returning, the lamp turns OFF after 30 minutes, when the interior lamp auto turn off condition is met.
note The interior lamp automatic shut-off time can be adjusted by the customise function (Refer to ).

IGNITION KEY CYLINDER ILLUMINATION LAMP CONTROL FUNCTION






  • With the ignition switch OFF, the lamp is illuminated when the driver’s door is opened, and it is turned off 30 seconds after the driver’s door is closed. However, the lamp is turned off if the ignition switch is turned ON or doors are locked within 30 seconds.
  • When the ignition key is removed from the ignition key cylinder, the lamp illuminates for 30 seconds after approximately 1 second (after the engine is stopped).